What it means
F6E4 lists the water float switch as the potential cause. JennAir wants the dishwasher checked for level, then a half-minute power cycle. An unlevel tub can trip the overfill float switch.
JennAir dishwasher F6E4 / Water
F6E4 lists the water float switch as the potential cause. JennAir wants the dishwasher checked for level, then a half-minute power cycle. An unlevel tub can trip the overfill float switch.
Also shown as F6E4
F6E4 lists the water float switch as the potential cause. JennAir wants the dishwasher checked for level, then a half-minute power cycle. An unlevel tub can trip the overfill float switch.
Set a level on the door or the rack rail and check side to side and front to back.
F6E4 returns on a level dishwasher.
Checks you have ticked / saved in this browser

Set a level on the door or the rack rail and check side to side and front to back. Incorrect leveling can actuate the overfill switch, as the page notes.

If the dishwasher rocks when you press the top corners, the feet are not set. Leveling feet are a built-in adjustment, not a reason to remove the unit.

Pull the plug or turn off the breaker for thirty seconds, then restore power.

Check that F6E4 stays away. If it returns on a level machine, book a visit.
Send the model and the checks you have already run, then begin your request from this page.
Book a visit
A simplified drawing, because layouts change with the model. Tap an outlined part to see a photo and the related check.

Component reference
The float switch watches for too much water.
Read the definitionThe float switch senses when the water level in the tub gets too high. It guards against overfilling, and JennAir's page names it for F6E4.
Read the supporting manualThe page says incorrect leveling can actuate the overfill or floater switch and cause the error. A tub that leans may shift the float even with a normal water level.
Read the supporting manualF8E4 reports water detected in the drip tray and includes install checks. F6E4 is about the float switch and leveling. Both mention a float switch, so read the code carefully.
Read the supporting manualManufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2026-06-15; PH 12197 / PH 12197 (dishwasher)
JennAir dishwasher page PH 12197, last modified 2026-06-15.
A small spirit level and an adjustable wrench or screwdriver for the feet are usually enough. Do not pull the dishwasher out if the connections are tight.
The page ties the error to leveling, which an installer sets. If it shows up soon after an install, say so when you book.
Not necessarily. Check the floor and the drip tray area anyway, and switch off power if you find water.
Then the page offers nothing further. A technician is needed for the switch or its connections.
Not as a step from the page. The float sits inside the tub, and the page does not describe cleaning it.
Code or symptom, part, service call
JennAir's reading page words F8E4 as Water Detected in Drip Tray. Turn off the water supply, press Cancel once to silence the tone, leave the door shut and do not turn the power off. The dishwasher drains and blocks operation. Then book a visit.
JennAir's order is power, then the door and lower rack, then water supply, control lock, delay start, and a one-minute reset. A dishwasher that will not fill adds the drain loop height and an interrupted-cycle flash to the list.
The float switch watches for too much water. JennAir F6E4 is "Water Float Switch", and the page asks if the dishwasher is level. F8E4 is "Water Detected in Drip Tray": check the supply connection, the float connector and empty the tray.
Schedule a diagnostic for your model, carried out at the appliance.
Office details, plus the access notes to pass along.