What it means
JennAir's dishwasher page describes F8E2 as a fill valve electric error. Remove the drip tray, inspect the inlet valve connection for leaks, then cycle the power. A repeat of the code calls for a technician.
JennAir dishwasher F8E2 / Water
JennAir's dishwasher page describes F8E2 as a fill valve electric error. Remove the drip tray, inspect the inlet valve connection for leaks, then cycle the power. A repeat of the code calls for a technician.
Also shown as F8E2
JennAir's dishwasher page describes F8E2 as a fill valve electric error. Remove the drip tray, inspect the inlet valve connection for leaks, then cycle the power. A repeat of the code calls for a technician.
Close the water shutoff to the dishwasher if there is any drip at the inlet.
F8E2 returns after the reset.
Checks you have ticked / saved in this browser

Close the water shutoff to the dishwasher if there is any drip at the inlet. Then switch off the power.

Take out the drip tray under the dishwasher and look at the inlet valve connection. JennAir prints this step. Check for leaks.

Look at the fitting for drips, damp spots or loose hose. Do not crank on fittings; a leaking connection belongs in a technician's hands.

Power the dishwasher down for half a minute, switch on again, and run a brief wash to see if F8E2 returns.
Send the model and the checks you have already run, then begin your request from this page.
Book a visitA simplified drawing, because layouts change with the model. Tap an outlined part to see a photo and the related check.

JennAir words it as a fill valve electric error. The valve is the part that lets water in under the control's command. Whatever is wrong is electrical, not a plumbing blockage.
Read the supporting manualThe page asks you to remove the drip tray and inspect the inlet valve connection, ensuring there is no leak. Water at the valve can also explain wet wiring.
Read the supporting manualF8E5 is the stuck-open valve, and its steps begin with shutting off the water. F8E2 is an electrical error on the same valve. Keep the two apart.
Read the supporting manualManufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2026-06-15; PH 12199 / PH 12199 (dishwasher)
JennAir dishwasher page PH 12199, last modified 2026-06-15.
JennAir asks you to remove the drip tray and inspect the inlet valve connection for leaks as its first step. Water near the valve can affect the electrical connection.
If you see any drip, close the shutoff and switch off the power first. Do that before pulling the drip tray out.
A dry tray is a good sign for the plumbing. Continue with the thirty-second power cycle; if F8E2 returns, book a technician.
JennAir describes it as an electrical error at the fill valve, not as an empty supply. H2O is the code for not detecting water.
We do not recommend it. The page gives no replacement steps, and the valve connects water and wiring in the same spot.
Code or symptom, part, service call
F8E5 on a JennAir dishwasher means Fill Valve Stuck Open. Turn off the water to the dishwasher if you can, press Cancel once to silence the tone, then shut the door and leave the power on. If you cannot turn the water off, turn off power to the dishwasher instead.
JennAir's order is power, then the door and lower rack, then water supply, control lock, delay start, and a one-minute reset. A dishwasher that will not fill adds the drain loop height and an interrupted-cycle flash to the list.
The fill valve lets water into the tub. JennAir F8E2 is "Fill Valve Electric Error" and F8E5 is "Fill Valve Stuck Open". F8E5 is urgent: turn off the water if you can, silence the tone with one Cancel press, and keep the door shut and the power on.
Schedule a diagnostic for your model, carried out at the appliance.
Office details, plus the access notes to pass along.