Start from the symptom
JennAir oven not heating.
Start with what JennAir lists: the door is fully closed, the breaker is on, a new install is wired correctly, and for gas the main valve is open. Elements cycling on and off is normal, and the control must not be locked or in demo mode.

Start with safe observations.
Turn the appliance off and unplug it before any check you can do yourself. Look out for pooled water and sharp edges. Never touch a wet plug or live area, take off service panels, or go past your model’s owner instructions.
- 1
Shut the door fully
Depending on the model, the elements will not come on with the door open. Opening the door in broil switches the broil element off at once.
- 2
Check the breaker or fuse (electric)
Re-engage a tripped breaker, or fit a new fuse if one blew. On a new electric install, check the strain relief, wire colors and terminal block nuts.
- 3
Check gas supply (gas and dual fuel)
Confirm the main gas valve and the shut-off on the pressure regulator are on. After an install, run a surface burner to purge air from the line.
- 4
Check the plug (gas)
Ignition needs a 120 V grounded working outlet. Do not use a two-prong adapter or extension cord.
- 5
Remove oven floor foil
Foil or a liner on the oven bottom can block air or gas flow to the burner.
- 6
Rule out lock, demo and delay
A locked control, demo mode or a delayed start can all stop heating.
Systems a technician may investigate.
The symptom connects to these parts. What you observed cannot show that any single one has failed.
If the display adds a code.
Heating element
FEE6 on a JennAir freestanding range names the main cavity bake element or its wiring. Let the oven cool, reset the breaker for about a minute and see whether the range still heats from the bottom.
Heating element
FEE7 on a JennAir freestanding range names the main cavity broil element or its wiring. Let the oven cool, reset the breaker for about a minute and test with a short broil only if the oven otherwise behaves.
Electrical supply
F9 E0 on a JennAir professional-style range or wall oven points at the electrical supply: the pro-range pages ask for the outlet or supply to be checked, and the wall oven page names wrong wiring at the supply with L2 and N swapped as the example. Have an electrician check before further use.
Read the related care guide.

Oven browning one side? Check the pans first.
Uneven baking in a JennAir oven usually comes from pans, preheating or rack position before it points to the oven. Dark pans brown more, shiny pans brown less, and food loaded early gets too much top heat. Fix those, then check level and airflow. [1][2]

Gas oven clicking? Here is the normal sound.
Short clicks while a JennAir gas oven preheats are normal: the igniter sparks until it detects a flame, and on a range that can repeat every 1 to 3 minutes. Clicking with no flame, or a gas smell, is different. Check the valves and the door, and stop if you smell gas. [1][2]
When observation becomes a service request.
Leave internal testing to a technician.
There is a gas smell, the oven still will not heat after these checks, or a code such as FEE6 or FEE7 shows. If you smell gas, leave and phone your gas utility before doing anything else. Then book a visit.
Arrange a diagnosticSources and model boundaries.
The JennAir oven not heating guidance rests on these references. Pick the manual that fits your model.
- Oven Not Heating - Powering On - Electric Range - Product Help | JennAir
- Circuit Breaker Tripped or Fuse Blown - Electric Range - Product Help | JennAir
- Oven Elements Turning On/Off - Electric Range - Product Help | JennAir
- Oven Not Working - Gas and Dual Fuel Range - Product Help | JennAir
- Oven Not Working - Cooktop Working - Clicking - Product Help | JennAir
- Oven Not Working - Cooktop Working - Not Clicking - Product Help | JennAir
- Broil Not Working - Range - Product Help | JennAir
Go by the instructions for your own model. See how we research these pages.
Are the oven elements supposed to turn off during baking?
Yes. JennAir says bake and broil elements cycle with a limiter at higher settings to avoid overheating, and the oven still holds the set temperature.
Why will my gas oven not heat when the cooktop works?
JennAir asks about an open door, items in the storage drawer, the regulator shut-off, the main gas valve, the outlet, and foil on the oven bottom.
Why does the broil element turn off?
Opening the door during broiling turns the broil element off immediately. It comes back when the door closes.
Could a power outage have stopped my oven?
Possibly. JennAir notes line noise after an outage can trigger an F9 code, and a breaker off for one minute is its first step.
Code or symptom, part, service call
Tie the message to what comes next.
FEE6
FEE6 on a JennAir freestanding range names the main cavity bake element or its wiring. Let the oven cool, reset the breaker for about a minute and see whether the range still heats from the bottom.
JennAir oven temperature problems
JennAir says not to judge oven temperature with a thermometer, because the elements cycle and most thermometers react too slowly. Check preheat time, racks, pan spacing and foil first, then run the biscuit test before any calibration.
Bake and broil elements
On JennAir ranges, FEE6 names the main cavity bake element and FEE7 the main cavity broil element, each with its wiring. The pages offer one owner step: a one-minute breaker reset. An element that stays cold afterwards needs a technician with the power off.
Oven repair
Schedule a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, plus the access notes to pass along.
