What it means
H2O, also printed F8E1 or H20, tells you the dishwasher cannot sense any water. Open the dishwasher's shutoff valve and straighten any kink in its feed hose, then press Start so it can try filling and carry on.
JennAir dishwasher H2O / Water
H2O, also printed F8E1 or H20, tells you the dishwasher cannot sense any water. Open the dishwasher's shutoff valve and straighten any kink in its feed hose, then press Start so it can try filling and carry on.
Also shown as H2O
H2O, also printed F8E1 or H20, tells you the dishwasher cannot sense any water. Open the dishwasher's shutoff valve and straighten any kink in its feed hose, then press Start so it can try filling and carry on.
Locate the small valve beneath the sink.
H2O shows again with the water on and the hose clear.
Checks you have ticked / saved in this browser

Locate the small valve beneath the sink. Make sure it is fully open.

Check the whole length of the feed hose for kinks. Straighten gently.

Once supply is corrected, press Start. The dishwasher will attempt to fill and resume the cycle.

You should hear water entering. If you hear nothing, stop and book a visit.
Send the model and the checks you have already run, then begin your request from this page.
Book a visitA simplified drawing, because layouts change with the model. Tap an outlined part to see a photo and the related check.

JennAir's page lists the cause as not detecting water. The dishwasher is waiting for water to arrive, and the control can't see it.
Read the supporting manualPages write the same code in different forms. The flash pattern is eight flashes, a pause and one flash, and the reading page writes H20 with a zero.
Read the supporting manualF8E2 concerns the fill valve's electrics, and F8E5 concerns a valve stuck open. H2O means no water arrived. It is a supply issue first.
Read the supporting manualManufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2026-06-15; PH 12206 / PH 12206 (dishwasher)
Manufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2026-06-15; PH 12178 / PH 12178 (dishwasher)
Manufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2026-08-31; PH 14220 / PH 14220 (dishwasher)
JennAir dishwasher pages PH 12178 and PH 12206, with the overview page PH 14220 (flash form: eight, pause, one).
JennAir's reading page writes the code with a zero, while the code page writes it with an O. They are the same message, also shown as F8E1.
Usually under the kitchen sink, on the supply line that feeds the dishwasher. It is separate from the sink faucet, so the sink can run while the dishwasher gets nothing.
Trace the supply hose end to end and look for a sharp bend or a flattened section. Straighten it gently and avoid pulling the fitting.
Press Start. JennAir says the dishwasher will attempt to fill and resume the cycle.
When the valve is open, the hose is straight and the code still returns. Give us the model and say whether you hear water entering.
Code or symptom, part, service call
JennAir's dishwasher page describes F8E2 as a fill valve electric error. Remove the drip tray, inspect the inlet valve connection for leaks, then cycle the power. A repeat of the code calls for a technician.
JennAir's order is power, then the door and lower rack, then water supply, control lock, delay start, and a one-minute reset. A dishwasher that will not fill adds the drain loop height and an interrupted-cycle flash to the list.
The fill valve lets water into the tub. JennAir F8E2 is "Fill Valve Electric Error" and F8E5 is "Fill Valve Stuck Open". F8E5 is urgent: turn off the water if you can, silence the tone with one Cancel press, and keep the door shut and the power on.
Schedule a diagnostic for your model, carried out at the appliance.
Office details, plus the access notes to pass along.