Model-specific code library

JennAir dishwasher error codes.

We decode all 19 printed codes: six get their own page (F9E1, F8E4, F8E5, F6E1, F7E2, F1E2) and 13 sit on family pages, plus six indicator-light rows. Eleven other codes searchers use are on one page that says JennAir does not print them.

Dishwasher code finder

F9E1 on a JennAir dishwasher is listed as Long Drain, meaning the water is not leaving the tub. The page's checks run from the filter to the drain hose, the sink disposer knockout plug on a new installation, the air gap and suds. Cycle the power after the checks.

Read the F9E1 checks
Or choose

25 researched dishwasher codes. Each model reads codes its own way, so go by your own manual.

Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work

Messages with a manual behind them.

All cycle and option lights flashing

Indicator lights

When every cycle and option light flashes together, the cycle has been suspended, most often because the door was opened mid-wash. Push the door shut until it latches; the lights stop and the cycle resumes after a short delay.

Information only
Clean light flashing (reading rule)

Indicator lights

A flashing Clean light usually carries an error code in two bursts. The first burst of rapid flashes is the F number; after a pause of a second or two, the second burst is the E number. Seven then one reads F7E1.

Owner checks first
Control light flashing

Indicator lights

The Control light flashes three times when you press a button while the controls are locked. Press and hold the Control Lock button for three seconds, on models that have one, to unlock. If it still flashes, wake the dishwasher from Sleep Mode.

Information only
F1E1

Controls

F1E1 on a JennAir dishwasher names the control module as the potential cause. Start by removing power for half a minute. The Clean light spells the code as a single flash, a gap, and a single flash again.

Reset, then book
F1E2

Controls

JennAir files F1E2 under main control communication errors for its dishwashers. The one remedy printed is a short loss of power, and a technician if the code comes back. On the Clean light, look for one flash, a gap, then two flashes.

Reset, then book
F2E1

Controls

JennAir's dishwasher page for F2E1 names a jammed key or a problem in the console. Tap each button once to feel for one that stays down, then leave the machine unpowered for half a minute. If F2E1 returns with no sticking key, schedule service.

Owner checks first
F2E2

Controls

F2E2 sits in JennAir's main control communication group for dishwashers. Leave it unpowered for half a minute, restore power and run a quick cycle. If F2E2 returns, schedule service. On the Clean light it is two flashes, a pause, then two more.

Reset, then book
F3E2

Sensors

F3E2 on a JennAir dishwasher lists a thermistor or an OWI sensor as the potential cause, both sensing parts. JennAir's answer is a thirty-second power loss, with service as the next step.

Reset, then book
F4E2

Heating

On JennAir's dishwasher page, F4E2 points to the heating system. The one step printed is thirty seconds without power; a repeat means service. The parts under the tub are for a technician only.

Reset, then book
F4E3

Heating

JennAir calls F4E3 a heating error. Take power away for thirty seconds; if F4E3 reappears, book a technician. Leave the parts in the base alone.

Reset, then book
F6E1

Controls

F6E1 on a JennAir dishwasher is listed as User Interface Error, Main Control. The page asks you to cycle the power for 30 seconds and to schedule service if the code comes back. The Clean light flashes it as six flashes, a pause, then one.

Reset, then book
F6E3

Water

F6E3 means excessive suds on JennAir's dishwasher page. Scoop out the foam, remove the dishes, add 2 to 3 tablespoons of vegetable oil, then run a full cycle with no detergent, followed by a cycle with the dispensers filled but no dishes.

Owner checks first
F6E4

Water

F6E4 lists the water float switch as the potential cause. JennAir wants the dishwasher checked for level, then a half-minute power cycle. An unlevel tub can trip the overfill float switch.

Owner checks first
F7E2

Motor

JennAir lists F7E2 as a wash motor error. Remove power for thirty seconds; a repeat of F7E2 calls for a technician. The wash motor drives the circulation pump, so listen for a hum without water movement.

Reset, then book
F8E2

Water

JennAir's dishwasher page describes F8E2 as a fill valve electric error. Remove the drip tray, inspect the inlet valve connection for leaks, then cycle the power. A repeat of the code calls for a technician.

Reset, then book
F8E4

Water

JennAir's reading page words F8E4 as Water Detected in Drip Tray. Turn off the water supply, press Cancel once to silence the tone, leave the door shut and do not turn the power off. The dishwasher drains and blocks operation. Then book a visit.

Urgent: act now
F8E5

Water

F8E5 on a JennAir dishwasher means Fill Valve Stuck Open. Turn off the water to the dishwasher if you can, press Cancel once to silence the tone, then shut the door and leave the power on. If you cannot turn the water off, turn off power to the dishwasher instead.

Urgent: act now
F9E1

Drain

F9E1 on a JennAir dishwasher is listed as Long Drain, meaning the water is not leaving the tub. The page's checks run from the filter to the drain hose, the sink disposer knockout plug on a new installation, the air gap and suds. Cycle the power after the checks.

Owner checks first
F9E2

Drain

JennAir lists F9E2 as an error with the drain motor. Check that the garbage disposer knockout plug is removed on a new install, clear any clog, straighten a kinked drain hose, verify the hose routing, then cycle power. Schedule service if it returns.

Reset, then book
FAE4

Diverter

FAE4, also written F10E4, lists a diverter valve error on JennAir's dishwasher page. JennAir's page asks for thirty seconds without power, and service if the code recurs. The diverter valve sends water between the spray arms.

Reset, then book
FAE5

Diverter

FAE5, also written F10E5, lists a diverter leak on JennAir's dishwasher page. Check under the dishwasher for leaks, make sure the water connections are secure, press Cancel twice, and try a new cycle. If the error returns, schedule service.

Reset, then book
Front status lights

Indicator lights

JennAir's front status light reports progress this way: blue while washing, red while drying, white when the cycle is complete, and blinking when it has paused. If it stays dark, JennAir asks for a 30-second power cycle.

Information only
H2O

Water

H2O, also printed F8E1 or H20, tells you the dishwasher cannot sense any water. Open the dishwasher's shutoff valve and straighten any kink in its feed hose, then press Start so it can try filling and carry on.

Owner checks first
Sani Rinse indicator glowing red

Indicator lights

The Sani Rinse indicator turns red when a cycle with the Sani Rinse option has finished successfully. If it does not light, the cycle was probably interrupted. A 30-second power cycle is JennAir's step for a misbehaving indicator.

Information only
Sanitize light flashing

Indicator lights

A flashing Sanitize light means the dishwasher did not reach the temperature needed for sanitizing, so the dishes were not sanitized. Check that the hot water at the dishwasher reaches at least 120 degrees F (49 C), and avoid opening the door mid-cycle.

Owner checks first

Start with the model boundary.

Dishwashers in a thoughtfully designed home

JennAir lists 19 dishwasher codes and no more.

We decode all 19 printed codes: six get their own page (F9E1, F8E4, F8E5, F6E1, F7E2, F1E2) and 13 sit on family pages, plus six indicator-light rows. Eleven other codes searchers use are on one page that says JennAir does not print them.

FCE1, FCE2, FCE3, FCE5, F3E3, F4E4, F5E1, F6E2, F6E7, F6E8 and F9E4 are printed in none of the JennAir pages we read. We do not infer a meaning from the nearest printed code.

Choose the next safe action.

Read the whole display

Count the first burst of Clean light flashes as F and the second as E, with a pause of one to two seconds between them. Write down the count before you cycle the power.

Respect the service boundary

If water is on the floor, stay clear of it and of the power supply. For F8E4 and F8E5, JennAir says to close the water supply, press Cancel once and keep the door shut; the power stays on unless the water cannot be turned off.

Documents checked for this library.

  • Dishwasher Error Codes - Reading - Product Help | JennAir
  • Clean Light Flashing - Dishwasher - Product Help | JennAir
  • F9E1 - Dishwasher - Product Help | JennAir
  • 8 Pause 1 Pause - pause, repeat - Error Code - Dishwasher - Product Help | JennAir
  • F8E5 - Dishwasher - Product Help | JennAir

Go by the instructions for your own model. See how we research these pages.

Here to help

Good questions.
Clear answers.

Talk to our team
Are these dishwasher meanings universal?

FCE1, FCE2, FCE3, FCE5, F3E3, F4E4, F5E1, F6E2, F6E7, F6E8 and F9E4 are printed in none of the JennAir pages we read. We do not infer a meaning from the nearest printed code.

What should I include when I report a dishwasher code?

Take a clear photo of the whole dishwasher display and of the model label. Add what the appliance was doing when the message came up, and do not borrow the explanation for a different appliance.

Why is a dishwasher code shown without any explanation?

An old search phrase is no substitute for manufacturer evidence. When our dishwasher documents leave a message undecoded, we show the name only and send you toward help, with no part or cause attached.

Where do I verify which dishwasher models a document applies to?

Browse the manufacturer documents in this dishwasher library and hold the models on their covers up against your label. Another model needs instructions of its own.

Let’s take care of it.

Something on the display?
Send us the details.