Inside the appliance
Dishwasher fill valve. In plain English.
The fill valve lets water into the tub. JennAir F8E2 is "Fill Valve Electric Error" and F8E5 is "Fill Valve Stuck Open". F8E5 is urgent: turn off the water if you can, silence the tone with one Cancel press, and keep the door shut and the power on.

Where it fits.
Dishwasher fill valve in the appliance
At the lower front corner of the cabinet, where the supply hose enters, behind the kick plate.
The picture shows the kind of component only. It cannot tell you which replacement suits your model.
What you notice when this system needs a look.
A Dishwasher fill valve concern may show up with a drop in performance or a code that keeps returning. Testing comes first, before anyone decides the component is to blame.

JennAir dishwasher won't start or fill
JennAir's order is power, then the door and lower rack, then water supply, control lock, delay start, and a one-minute reset. A dishwasher that will not fill adds the drain loop height and an interrupted-cycle flash to the list.

JennAir dishwasher lights flashing
Which light flashes decides the answer. A flashing Clean light is usually an F-then-E code, a Sanitize light means the sanitize heat was not reached, and all lights flashing means the door was opened mid-cycle.
Owner care, within the model instructions.
Turn the appliance off and unplug it before any check you can do yourself. Look out for pooled water and sharp edges. Never touch a wet plug or live area, take off service panels, or go past your model’s owner instructions.
- 1
F8E5: water first
Turn off the water supply to the dishwasher if possible. Press Cancel once to silence the alarm, then shut the door. Do not turn off the power and keep the door closed.
- 2
If you cannot stop the water
The page then says to turn off power to the dishwasher instead. Mop up water that reaches the floor.
- 3
F8E2: inspect the inlet
Remove the drip tray and look at the inlet valve connection for leaks, then cycle the power for 30 seconds.
- 4
H2O is the opposite
H2O means the dishwasher does not detect water. Check the supply is on and the supply hose has no kinks.
Cleaning or replacement?
Leave internal testing to a technician.
Book us for any F8E5, even if the water seems to have stopped.
Book us if F8E2 returns after the inlet check and power cycle.
Book us if the tub keeps filling or the floor gets wet.
Arrange a diagnosticSources and model boundaries.
The Dishwasher fill valve guidance rests on these references. Pick the manual that fits your model.
- F8E2- Dishwasher - Product Help | JennAir
- F8E5 - Dishwasher - Product Help | JennAir
- H2O - Dishwasher - Product Help | JennAir
- F8E4 - Dishwasher - Product Help | JennAir
Go by the instructions for your own model. See how we research these pages.
Why must I keep the power on for F8E5?
The JennAir page says not to turn off the power and to keep the door closed, since the control runs a drain sequence. Only cut power if you cannot close the water.
What does F8E2 mean?
The potential cause is a fill valve electric error. The page asks you to inspect the inlet connection for leaks and cycle the power.
Where is the water shutoff?
Usually under the sink on the supply line to the dishwasher. Your installation sheet shows it.
Is F8E5 safe to ignore?
No. A valve stuck open can keep filling the tub. Shut off the water and book a visit.
Code or symptom, part, service call
Tie the message to what comes next.
JennAir dishwasher won't start or fill
JennAir's order is power, then the door and lower rack, then water supply, control lock, delay start, and a one-minute reset. A dishwasher that will not fill adds the drain loop height and an interrupted-cycle flash to the list.
Dishwasher repair
Schedule a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, plus the access notes to pass along.

