Inside the appliance
Dishwasher diverter valve. In plain English.
The diverter valve sends water to different spray arms. JennAir FAE4 (also printed F10E4) is "Diverter Valve Error", and FAE5 (F10E5) is "Diverter Leak". For FAE5 the page asks you to look for leaks and connections, press Cancel twice and try a new cycle.

Where it fits.
Dishwasher diverter valve in the appliance
Under the tub in the water path that feeds the spray arms.
The picture shows the kind of component only. It cannot tell you which replacement suits your model.
What you notice when this system needs a look.
A Dishwasher diverter valve concern may show up with a drop in performance or a code that keeps returning. Testing comes first, before anyone decides the component is to blame.

JennAir dishwasher won't start or fill
JennAir's order is power, then the door and lower rack, then water supply, control lock, delay start, and a one-minute reset. A dishwasher that will not fill adds the drain loop height and an interrupted-cycle flash to the list.

JennAir dishwasher lights flashing
Which light flashes decides the answer. A flashing Clean light is usually an F-then-E code, a Sanitize light means the sanitize heat was not reached, and all lights flashing means the door was opened mid-cycle.
Owner care, within the model instructions.
Turn the appliance off and unplug it before any check you can do yourself. Look out for pooled water and sharp edges. Never touch a wet plug or live area, take off service panels, or go past your model’s owner instructions.
- 1
FAE4: power cycle
The FAE4 or F10E4 page lists a power cycle only. The Product Help reset for dishwashers is 30 seconds without power: unplug it, or switch the breaker off at the panel, then restore it.
- 2
FAE5: look under the unit
Check for water under the dishwasher and make sure all connections are secure.
- 3
FAE5: clear and retry
Press Cancel twice and try starting a new cycle. If the error returns, the page says to schedule service.
- 4
Flashing-light models
If your dishwasher blinks rather than prints a code, the JennAir reading guide explains how to count the F and E flashes and the pauses between them.
Cleaning or replacement?
Leave internal testing to a technician.
Book us if FAE4 or FAE5 returns.
Book us if you find water under the dishwasher and cannot trace it to a loose line.
Book us if only some spray arms run.
Arrange a diagnosticSources and model boundaries.
The Dishwasher diverter valve guidance rests on these references. Pick the manual that fits your model.
- FAE4 or F10E4 - Dishwasher - Product Help | JennAir
- FAE5 or F10E5 - Dishwasher - Product Help | JennAir
- Dishwasher Leaking Troubleshooting Guide - Product Help | JennAir
Go by the instructions for your own model. See how we research these pages.
Why does the code have two names?
JennAir prints FAE4 or F10E4 and FAE5 or F10E5 on one page each, so both spellings refer to the same code. Your display shows one of them.
Does FAE5 mean water is leaking out?
The potential cause is a diverter leak. The page asks you to look for leaks under the unit and confirm the connections.
Can I keep running the dishwasher?
The page allows a new cycle after Cancel is pressed twice. If the error returns, stop and book.
Is the diverter user serviceable?
No help page describes a replacement. A technician does that after testing.
Code or symptom, part, service call
Tie the message to what comes next.
JennAir dishwasher won't start or fill
JennAir's order is power, then the door and lower rack, then water supply, control lock, delay start, and a one-minute reset. A dishwasher that will not fill adds the drain loop height and an interrupted-cycle flash to the list.
Dishwasher repair
Schedule a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, plus the access notes to pass along.

