Inside the appliance
Dishwasher drain motor and hose. In plain English.
JennAir F9E1 is "Long Drain" and F9E2 is "Drain motor error". Before booking, check the drain hose, the disposer knockout plug, the filter and the high loop. These setup problems cause most of the draining complaints the help pages describe.

Where it fits.
Dishwasher drain motor and hose in the appliance
The drain pump sits under the tub near the sump. The hose runs from the back of the dishwasher to the sink drain or disposer.
The picture shows the kind of component only. It cannot tell you which replacement suits your model.
What you notice when this system needs a look.
A Dishwasher drain motor and hose concern may show up with a drop in performance or a code that keeps returning. Testing comes first, before anyone decides the component is to blame.

JennAir dishwasher won't start or fill
JennAir's order is power, then the door and lower rack, then water supply, control lock, delay start, and a one-minute reset. A dishwasher that will not fill adds the drain loop height and an interrupted-cycle flash to the list.

JennAir dishwasher lights flashing
Which light flashes decides the answer. A flashing Clean light is usually an F-then-E code, a Sanitize light means the sanitize heat was not reached, and all lights flashing means the door was opened mid-cycle.
Owner care, within the model instructions.
Turn the appliance off and unplug it before any check you can do yourself. Look out for pooled water and sharp edges. Never touch a wet plug or live area, take off service panels, or go past your model’s owner instructions.
- 1
Clear the filter
F9E1 asks you to remove the filter and clean it thoroughly under running water. Do not run the dishwasher without the filters seated.
- 2
Follow the hose
Look for a hose that is kinked, crushed or blocked from the back of the dishwasher to the sink, routed on the correct side and inside the frame on a new install.
- 3
Check the disposer
If connected, run the disposer to clear food and confirm the knockout plug was removed on a new installation.
- 4
Check the loop
The drain hose should form a high loop or meet an air gap. A hose that sits low can let water flow back into the tub.
- 5
Cycle the power
The Product Help reset for dishwashers is 30 seconds without power: unplug it, or switch the breaker off at the panel, then restore it.
Cleaning or replacement?
Leave internal testing to a technician.
Book us if F9E2 returns after the hose and disposer checks.
Book us if water remains after a drain cycle with a clean filter.
Book us if the drain pump hums but no water leaves.
Arrange a diagnosticSources and model boundaries.
The Dishwasher drain motor and hose guidance rests on these references. Pick the manual that fits your model.
- F9E1 - Dishwasher - Product Help | JennAir
- F9E2 - Dishwasher - Product Help | JennAir
- Checking the Drain Loop Height - Product Help | JennAir
- Newly Installed Dishwasher Not Draining - Product Help | JennAir
- Cleaning the Removable Filtration System - Dishwasher - Product Help | JennAir
Go by the instructions for your own model. See how we research these pages.
What is the difference between F9E1 and F9E2?
F9E1 is labeled Long Drain and lists hose, filter, disposer and air gap checks. F9E2 is labeled Drain motor error, with the same hose checks first.
My dishwasher is new. Why will it not drain?
JennAir lists a kinked or misrouted hose, a missing high loop or air gap, and a disposer knockout plug that was not removed.
Do suds matter?
The F9E1 page asks about excessive suds. Dish soap makes foam that can push water out. Use only detergent made for automatic dishwashers.
Where do I find the knockout plug?
In the inlet of the garbage disposer. The help library has a page on connecting the dishwasher drain to a disposer.
Code or symptom, part, service call
Tie the message to what comes next.
JennAir dishwasher won't start or fill
JennAir's order is power, then the door and lower rack, then water supply, control lock, delay start, and a one-minute reset. A dishwasher that will not fill adds the drain loop height and an interrupted-cycle flash to the list.
Dishwasher repair
Schedule a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, plus the access notes to pass along.

