Start from the symptom

JennAir dishwasher lights flashing.

Which light flashes decides the answer. A flashing Clean light is usually an F-then-E code, a Sanitize light means the sanitize heat was not reached, and all lights flashing means the door was opened mid-cycle.

Last reviewed

Closed black-glass dishwasher door in a dim kitchen, with a row of small indicator lamps lit along the top edge and a soft light glowing on the tile below.
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work

Start with safe observations.

Turn the appliance off and unplug it before any check you can do yourself. Look out for pooled water and sharp edges. Never touch a wet plug or live area, take off service panels, or go past your model’s owner instructions.

  1. 1

    Read the Clean light

    Count the first group of quick flashes as the F number, wait for the 1 to 2 second pause, count the second group as the E number. Seven flashes, a pause, then one flash is F7E1.

  2. 2

    Sanitize light

    It flashes when the sanitize temperature was not met, and the dishes were not sanitized. Run hot water for 30 seconds; JennAir wants at least 120 F at the tap.

  3. 3

    All cycle lights

    They flash when the door was opened mid-cycle. Close it firmly until it latches and the cycle resumes after a short delay.

  4. 4

    Control light

    It flashes three times when a key is pressed during control lock. Hold Control Lock for three seconds, or wake the panel from sleep mode.

  5. 5

    Front status lights

    Blue means washing, red drying, white finished, blinking paused. A Sani Rinse light that glows red at the end means the option finished.

  6. 6

    Reset

    Cut power for 30 seconds, then restore it. A code that returns should be looked up by its F and E numbers.

Systems a technician may investigate.

We name no part before the visit. After the diagnostic the technician tells you which part, if any, has failed, and matches it to your model and serial number before anything is replaced.

Part

Dishwasher wash motor

The wash motor spins the circulation pump that pushes water to the spray arms. JennAir F7E2 reads "Wash Motor Error". The page gives one step, a power cycle, and says to schedule service if the code comes back.

Part

Dishwasher drain motor and hose

JennAir F9E1 is "Long Drain" and F9E2 is "Drain motor error". Before booking, check the drain hose, the disposer knockout plug, the filter and the high loop. These setup problems cause most of the draining complaints the help pages describe.

Part

Dishwasher fill valve

The fill valve lets water into the tub. JennAir F8E2 is "Fill Valve Electric Error" and F8E5 is "Fill Valve Stuck Open". F8E5 is urgent: turn off the water if you can, silence the tone with one Cancel press, and keep the door shut and the power on.

Part

Dishwasher heating system

JennAir F4E2 names the heating system and F4E3 a heating error. Each page gives a power cycle and says to schedule service if the code comes back. A heating code can show up as dishes that are wet or not sanitized, so note the cycle you were running.

Part

Dishwasher diverter valve

The diverter valve sends water to different spray arms. JennAir FAE4 (also printed F10E4) is "Diverter Valve Error", and FAE5 (F10E5) is "Diverter Leak". For FAE5 the page asks you to look for leaks and connections, press Cancel twice and try a new cycle.

Part

Float switch and drip tray

The float switch watches for too much water. JennAir F6E4 is "Water Float Switch", and the page asks if the dishwasher is level. F8E4 is "Water Detected in Drip Tray": check the supply connection, the float connector and empty the tray.

Part

Dishwasher thermistor and OWI sensor

JennAir F3E2 names the thermistor or OWI sensor, the temperature and water sensing part. The page gives a power cycle and says to schedule service if the code returns. It is a good example of a code that names a part and gives the owner a single step.

Part

Dishwasher removable filter

JennAir dishwashers with a removable filter ask you to clean it by hand under running water, with a soft brush for hard-water deposits. Abrasive pads and wire brushes are out, and the dishwasher should not operate without both filters in place.

If the display adds a code.

Clean light flashing (reading rule)Owner checks first

Indicator lights

A flashing Clean light usually carries an error code in two bursts. The first burst of rapid flashes is the F number; after a pause of a second or two, the second burst is the E number. Seven then one reads F7E1.

Sanitize light flashingOwner checks first

Indicator lights

A flashing Sanitize light means the dishwasher did not reach the temperature needed for sanitizing, so the dishes were not sanitized. Check that the hot water at the dishwasher reaches at least 120 degrees F (49 C), and avoid opening the door mid-cycle.

Control light flashingInformation only

Indicator lights

The Control light flashes three times when you press a button while the controls are locked. Press and hold the Control Lock button for three seconds, on models that have one, to unlock. If it still flashes, wake the dishwasher from Sleep Mode.

All cycle and option lights flashingInformation only

Indicator lights

When every cycle and option light flashes together, the cycle has been suspended, most often because the door was opened mid-wash. Push the door shut until it latches; the lights stop and the cycle resumes after a short delay.

Front status lightsInformation only

Indicator lights

JennAir's front status light reports progress this way: blue while washing, red while drying, white when the cycle is complete, and blinking when it has paused. If it stays dark, JennAir asks for a 30-second power cycle.

Sani Rinse indicator glowing redInformation only

Indicator lights

The Sani Rinse indicator turns red when a cycle with the Sani Rinse option has finished successfully. If it does not light, the cycle was probably interrupted. A 30-second power cycle is JennAir's step for a misbehaving indicator.

When observation becomes a service request.

Leave internal testing to a technician.

A code returns after the 30 second reset, the lights stay dark, or the sanitize light keeps flashing with hot water at the tap. Schedule a technician visit.

Arrange a diagnostic

Sources and model boundaries.

The JennAir dishwasher lights flashing guidance rests on these references. Pick the manual that fits your model.

  • Clean Light Flashing - Dishwasher - Product Help | JennAir
  • Sanitize Light Flashing - Dishwasher - Product Help | JennAir
  • Control Light Flashing - Dishwasher - Product Help | JennAir
  • All Cycle And Option Lights flashing - Dishwasher - Product Help | JennAir
  • Front Status Lights - Dishwasher - Product Help | JennAir
  • Front Status Lights Not Illuminated - Dishwasher - Product Help | JennAir
  • Glowing Red - Dishwasher - Product Help | JennAir
  • Using Control Lock - Product Help | JennAir

Go by the instructions for your own model. See how we research these pages.

Here to help

Good questions.
Clear answers.

Talk to our team
How do I read a JennAir dishwasher blinking code?

Count the first quick set as F, wait about 2 seconds, then count the second set as E. After a longer pause of about 5 seconds the pattern repeats.

Why is the Sanitize light flashing?

JennAir says the temperature needed for sanitizing was not reached, so the dishes were not sanitized. Check that hot water at the tap reaches at least 120 F.

Why do all cycle lights flash?

The door was opened during a running cycle, which suspends it. Latch the door firmly and the cycle resumes by itself.

What do the front status colors mean?

JennAir lists blue for washing, red for drying, white for done and blinking for paused.

Let’s take care of it.

Something on the display?
Send us the details.