Inside the appliance
Float switch and drip tray. In plain English.
The float switch watches for too much water. JennAir F6E4 is "Water Float Switch", and the page asks if the dishwasher is level. F8E4 is "Water Detected in Drip Tray": check the supply connection, the float connector and empty the tray.

Where it fits.
Float switch and drip tray in the appliance
The float sits in the base pan under the tub. The drip tray is the removable plastic tray at the bottom front.
The picture shows the kind of component only. It cannot tell you which replacement suits your model.
What you notice when this system needs a look.
A Float switch and drip tray concern may show up with a drop in performance or a code that keeps returning. Testing comes first, before anyone decides the component is to blame.

JennAir dishwasher won't start or fill
JennAir's order is power, then the door and lower rack, then water supply, control lock, delay start, and a one-minute reset. A dishwasher that will not fill adds the drain loop height and an interrupted-cycle flash to the list.

JennAir dishwasher lights flashing
Which light flashes decides the answer. A flashing Clean light is usually an F-then-E code, a Sanitize light means the sanitize heat was not reached, and all lights flashing means the door was opened mid-cycle.
Owner care, within the model instructions.
Turn the appliance off and unplug it before any check you can do yourself. Look out for pooled water and sharp edges. Never touch a wet plug or live area, take off service panels, or go past your model’s owner instructions.
- 1
F6E4: level the unit
The page says incorrect leveling can actuate the overfill or floater switch and cause the error. Check the dishwasher with a level, or the phone leveling tool JennAir links to.
- 2
F8E4: look for water
Open the door and check for water. Check the water supply connections: the rubber washer must seat, and the 90-degree elbow tightens by hand.
- 3
F8E4: check the connector
Confirm the float switch connector is pushed in until the locking tab shows, and the power cord does not touch the motor or the lower tub.
- 4
Empty the drip tray
Press the snaps on each side of the tray toward the center and pull it out gently; the float wire is still attached.
- 5
Clear the code
Press Cancel once to silence the alarm, then again to clear the code.
Cleaning or replacement?
Leave internal testing to a technician.
Book us if F8E4 returns after the tray is emptied and connections checked.
Book us if the drip tray fills again within a day.
Book us if F6E4 returns on a unit you have already leveled.
Arrange a diagnosticSources and model boundaries.
The Float switch and drip tray guidance rests on these references. Pick the manual that fits your model.
- F6E4- Dishwasher - Product Help | JennAir
- F8E4 - Dishwasher - Product Help | JennAir
- Dishwasher Error Codes - Reading - Product Help | JennAir
- F8E4 - Error Code - Dishwasher - Product Help | JennAir
Go by the instructions for your own model. See how we research these pages.
Why does the dishwasher need to be level?
The F6E4 page says an unlevel unit can trip the overfill switch. Level it side to side and front to back.
What does F8E4 mean?
The Dishwasher Error Codes - Reading page prints it as Water Detected in Drip Tray. The F8E4 page itself lists checks without a cause line.
Is F8E4 urgent?
It can be. The page says the drain sequence begins and operation is prevented; keep the door closed and the power on until the sequence ends.
What if I see suds?
The F8E4 page asks about excessive suds. Use dishwasher detergent only, and let suds settle before another cycle.
Code or symptom, part, service call
Tie the message to what comes next.
JennAir dishwasher won't start or fill
JennAir's order is power, then the door and lower rack, then water supply, control lock, delay start, and a one-minute reset. A dishwasher that will not fill adds the drain loop height and an interrupted-cycle flash to the list.
Dishwasher repair
Schedule a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, plus the access notes to pass along.

