Inside the appliance
Dishwasher removable filter. In plain English.
JennAir dishwashers with a removable filter ask you to clean it by hand under running water, with a soft brush for hard-water deposits. Abrasive pads and wire brushes are out, and the dishwasher should not operate without both filters in place.

Where it fits.
Dishwasher removable filter in the appliance
On the floor of the tub under the lower rack, or a foreign object cup in front of the pump on Style 2 models.
The picture shows the kind of component only. It cannot tell you which replacement suits your model.
What you notice when this system needs a look.
A Dishwasher removable filter concern may show up with a drop in performance or a code that keeps returning. Testing comes first, before anyone decides the component is to blame.

JennAir dishwasher won't start or fill
JennAir's order is power, then the door and lower rack, then water supply, control lock, delay start, and a one-minute reset. A dishwasher that will not fill adds the drain loop height and an interrupted-cycle flash to the list.

JennAir dishwasher lights flashing
Which light flashes decides the answer. A flashing Clean light is usually an F-then-E code, a Sanitize light means the sanitize heat was not reached, and all lights flashing means the door was opened mid-cycle.
Owner care, within the model instructions.
Turn the appliance off and unplug it before any check you can do yourself. Look out for pooled water and sharp edges. Never touch a wet plug or live area, take off service panels, or go past your model’s owner instructions.
- 1
Clear large debris first
Remove toothpicks, broken glass or olive pits from around the filter area by hand before you lift the filters, so they do not drop into the pump area.
- 2
Rinse and brush softly
Rinse under running water until most soil is gone. A soft brush is allowed for hard-water deposits; wire brushes and abrasive pads can damage the filter.
- 3
Know your style
Style 1 filters come out and are cleaned. Style 2 models use a foreign object cup below the lower rack instead, which you empty when full.
- 4
Seat everything
Reinstall so the filters are locked in. The page warns that running the machine with the filters missing or unlocked can damage it.
Cleaning or replacement?
Leave internal testing to a technician.
Book us if cleaning the filter does not stop a poor drain or a gritty film on dishes.
Book us if the filter housing is cracked or does not lock.
Book us if a drain code returns with a clean filter.
Arrange a diagnosticSources and model boundaries.
The Dishwasher removable filter guidance rests on these references. Pick the manual that fits your model.
- Cleaning the Removable Filtration System - Dishwasher - Product Help | JennAir
- Cleaning the Filter - Product Help | JennAir
- F9E1 - Dishwasher - Product Help | JennAir
Go by the instructions for your own model. See how we research these pages.
How often should I clean it?
The pages say to clean it when needed and give no schedule. Check it if dishes look gritty or the tub drains slowly.
Can I run a cycle with the filter out?
No. The JennAir page warns that running a cycle with the filters missing or loose may damage the machine.
What is the foreign object cup?
On Style 2 models it protects the pump. Press the center tab, pull the cup up, empty it and push it back to lock.
Does a clean filter fix F9E1?
It is the first check on that page, along with the hose, disposer and air gap. The code can still mean a drain problem beyond the filter.
Code or symptom, part, service call
Tie the message to what comes next.
JennAir dishwasher won't start or fill
JennAir's order is power, then the door and lower rack, then water supply, control lock, delay start, and a one-minute reset. A dishwasher that will not fill adds the drain loop height and an interrupted-cycle flash to the list.
Dishwasher repair
Schedule a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, plus the access notes to pass along.

