Inside the appliance
Oven temperature sensor. In plain English.
JennAir Product Help ties F1, F2 and several F3 codes to the oven temperature sensor, the control or the wiring between them. The sensor reports cavity heat to the control. The help pages pair it with the control, so one reset is the only owner step.

Where it fits.
Oven temperature sensor in the appliance
Inside the oven cavity, wired back to the control. The help pages give no position, so it varies by model.
The picture shows the kind of component only. It cannot tell you which replacement suits your model.
What you notice when this system needs a look.
A Oven temperature sensor concern may show up with a drop in performance or a code that keeps returning. Testing comes first, before anyone decides the component is to blame.

JennAir oven temperature problems
JennAir says not to judge oven temperature with a thermometer, because the elements cycle and most thermometers react too slowly. Check preheat time, racks, pan spacing and foil first, then run the biscuit test before any calibration.

JennAir range burner problems
Find your cooktop type first. Glowing that cycles on and off is normal on electric coil and glass tops, and gas flame trouble starts with clean ports and a seated cap. LP conversion or a wrong gas type needs a technician.
Owner care, within the model instructions.
Turn the appliance off and unplug it before any check you can do yourself. Look out for pooled water and sharp edges. Never touch a wet plug or live area, take off service panels, or go past your model’s owner instructions.
- 1
Read the whole code
F1, F2 and F3 are only the start. The digit after E matters: F3 E3 names the sensor and its wiring on a range, while F3 E0 pairs the sensor with the control, and on a wall oven names the upper or lower oven.
- 2
Reset once
The Product Help pages say to switch the oven off at its breaker for one minute, switch it back on and watch it for a minute. If the code stays off, run a normal cycle.
- 3
Separate a code from a drift
A sensor that reads a few degrees off is not an error code. The calibration pages describe a biscuit test and a 30-degree adjustment range on models that offer it. Run that before blaming a part.
- 4
Note the cooking mode
Tell us whether the code shows during preheat, bake or self-clean. The pages do not rank those, but the answer helps the technician start in the right place.
Cleaning or replacement?
Leave internal testing to a technician.
Book us if an F1, F2 or F3 code comes back after the one-minute reset.
Book us if the oven heats but the biscuit test still shows temperatures far from the dial.
Book us before using self-clean while any temperature code keeps showing.
Arrange a diagnosticSources and model boundaries.
The Oven temperature sensor guidance rests on these references. Pick the manual that fits your model.
- F1 - Error Code - Range - Product Help | JennAir
- F1 - Wall Oven - Product Help | JennAir
- F3 E3 - Error Code - Range - Product Help | JennAir
- F3 E3 - Wall Oven - Product Help | JennAir
- F3 E0 - Error Code - Range - Product Help | JennAir
- F3 E0 - Wall Oven - Product Help | JennAir
- How to Calibrate the Oven - Product Help | JennAir
- How to Evaluate if Temperature Calibration is Needed - Product Help | JennAir
Go by the instructions for your own model. See how we research these pages.
Does an F1 code always mean a bad sensor?
No. The JennAir page says there may be a problem with the sensor, the control or the wiring. It names three suspects and one reset, so the cause is confirmed by testing.
Where is the sensor in a JennAir oven?
The help pages do not place it. Your owner literature or a technician with your model number can show where it sits in that cavity.
Can I calibrate instead of replacing it?
Calibration is a separate adjustment for a slow or fast oven, set between minus 30 and plus 30 degrees on models that offer it. It does not clear a sensor code.
Is the same code worded alike on ranges and wall ovens?
For F1 the wording matches. F3 E0 differs: it names the upper oven sensor on a wall oven, and F3 E3 pairs the sensor with the control there. Check your appliance type.
Code or symptom, part, service call
Tie the message to what comes next.
JennAir oven temperature problems
JennAir says not to judge oven temperature with a thermometer, because the elements cycle and most thermometers react too slowly. Check preheat time, racks, pan spacing and foil first, then run the biscuit test before any calibration.
Oven repair
Schedule a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, plus the access notes to pass along.

