Start from the symptom

JennAir oven range burner problems.

Find your cooktop type first. Glowing that cycles on and off is normal on electric coil and glass tops, and gas flame trouble starts with clean ports and a seated cap. LP conversion or a wrong gas type needs a technician.

Last reviewed

Gas burner with an uneven yellow-orange flame on only half of its ports, while a hand holds a saucepan lifted away to one side.
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work

Start with safe observations.

Turn the appliance off and unplug it before any check you can do yourself. Look out for pooled water and sharp edges. Never touch a wet plug or live area, take off service panels, or go past your model’s owner instructions.

  1. 1

    Electric coil: know the new coils

    JennAir says coil elements changed in June 2018 to temperature-limiting coils. The outer coil stays on but glows less, the inner coil cycles, and large pots may heat slower. Push the knob in before turning it.

  2. 2

    Glass top: cycling is normal

    The elements cycle to protect the glass, and at low settings such as Keep Warm they may not glow at all. Check the control lock, power cord and breaker, and reset the range.

  3. 3

    Glass top too hot

    Check whether a dual or triple element is selected, since combined sizes suit large cookware and canning.

  4. 4

    Gas: clean ports and seat the caps

    With controls off and the top cool, clear ports with a straight pin, needle or fine wire, never a wooden toothpick, and refit the correct cap on its base.

  5. 5

    Gas: odd flame color

    JennAir links colored flames to minerals from an ultrasonic humidifier in the house, a misplaced cap or clogged ports.

  6. 6

    Gas: tall yellow flames or LP gas

    A cooktop converted to LP but connected to natural gas runs tall and yellow. On LP, a poor conversion shows as a flame problem and JennAir says to call for service.

  7. 7

    Gas: popping or a stuck knob

    Wet burners pop until dry. A knob that will not turn needs to be pushed in first, and it must be installed to match the valve stem.

Systems a technician may investigate.

We name no part before the visit. After the diagnostic the technician tells you which part, if any, has failed, and matches it to your model and serial number before anything is replaced.

Part

Oven temperature sensor

JennAir Product Help ties F1, F2 and several F3 codes to the oven temperature sensor, the control or the wiring between them. The sensor reports cavity heat to the control. The help pages pair it with the control, so one reset is the only owner step.

Part

Oven door latch assembly

The latch assembly and its door switch lock the oven door for self-clean and report that the door is closed. JennAir lists them for F5 codes and F7 E0, and for the locked-door and door-will-not-close pages. A bent latch arm is one check you can do yourself.

Part

Oven electronic control

The electronic control is the board that manages the oven functions. JennAir names it in F1 E1, F3 and F4 codes, and as the shared suspect in many sensor and keypad codes. The help pages give one owner step, a one-minute power-down, and do not name a repair.

Part

Appliance manager control

JennAir ranges and wall ovens with several cavities use an appliance manager that coordinates the oven controls. The F6 family names it, sometimes with the converter control or the user interface. The pages admit there are many possible reasons, then give one reset.

Part

Oven cooling fan

JennAir ovens run a cooling fan during and after use, and the pages say that humming is normal. An F8 E0 code is different: it says the fan speed is too low and points to an airflow restriction, the fan or its wiring. Check for blocked airflow, reset, then book.

Part

Meat probe receptacle

Several JennAir F3 and F8 codes come from the meat probe. The pages ask you to confirm the probe is seated in its receptacle, and on some wall ovens to check a power attachment on the roll-out rack. These are quick owner checks before any reset.

Part

Oven keypad and user interface

The user interface is the keypad or touch panel you press. JennAir lists it in the F2 family (F2 E0 to F2 E6), where F2 E1 often means a key is stuck or held too long. The help pages suggest checking cooktop grates on some ranges, then a one-minute reset.

Part

Oven Wi-Fi module

The Wi-Fi module links a connected JennAir oven to your router. FC E1 to FC E3 mean the appliance could not connect; FC E4 and FC E5 name the antenna; FC E6 and FC E9 name the power module. A router restart is the first owner step; the oven itself still bakes.

Part

Steam oven water system

Wall ovens with steam keep water in a removable container and a boiler. JennAir names the water level sensor, the boiler temperature sensor, the water filter and the conductivity sensor in F7 E0 to F7 E4. The routine messages (descale, refill, empty) are owner tasks.

Part

Bake and broil elements

On JennAir ranges, FEE6 names the main cavity bake element and FEE7 the main cavity broil element, each with its wiring. The pages offer one owner step: a one-minute breaker reset. An element that stays cold afterwards needs a technician with the power off.

When observation becomes a service request.

Leave internal testing to a technician.

Flames are very tall, yellow or uneven after cleaning, an LP conversion is suspected, or a coil or glass element stays dead after the power checks. If you ever smell gas, leave and call your gas utility before anything else. Then schedule a technician visit.

Arrange a diagnostic

Sources and model boundaries.

The JennAir range burner problems guidance rests on these references. Pick the manual that fits your model.

  • Coil Element Not Glowing Like Before - Product Help | JennAir
  • Coil Element Not Working - Product Help | JennAir
  • Burners Not Glowing - Glass Cooktop - Product Help | JennAir
  • Element(s) Not Working - Glass Cooktop - Product Help | JennAir
  • Element(s) Too Hot - Glass Cooktop - Product Help | JennAir
  • Cooktop Element(s) Cycle Off and On - Product Help | JennAir
  • Burner Flames Abnormal Colors - Natural Gas - Product Help | JennAir
  • Burner Flames Too High - Natural Gas - Product Help | JennAir
  • Burner Flames Abnormal Colors - LP Gas - Product Help | JennAir
  • Knob Won't Turn - Range - Product Help | JennAir

Go by the instructions for your own model. See how we research these pages.

Here to help

Good questions.
Clear answers.

Talk to our team
Why does my glass cooktop element go on and off?

The elements cycle to keep the glass from overheating. JennAir says this holds even at the highest setting and that low settings may not glow at all.

Why are my new coil elements not glowing as red?

Coils sold since June 2018 are temperature-limiting. JennAir says the outer coil may glow less and the inner one cycles, which is normal.

What causes orange or pink gas flames?

JennAir points to minerals from an ultrasonic humidifier, such as calcium for orange and potassium for pink, or a cap or port problem.

Can I clean burner ports with a toothpick?

No. JennAir says a wooden toothpick can break off and block gas flow. Use a straight pin, needle or fine wire without enlarging the port.

Let’s take care of it.

Something on the display?
Send us the details.