On this page
- Steam softens hard-soiled particles and makes cleaning easier. 13
- Do not use oven cleaners or other additives with Steam Clean. 12
- Leave the door shut while the cycle runs, since the water is hot. 12
- On a range, the oven must be below 170°F, and the cycle takes 50 minutes. 2
- A second cycle can help if soil remains. 13
What does Steam Clean do in a JennAir oven?#
It softens soil. JennAir says the Steam Cleaning function loosens hard-soiled particles and makes cleaning easier, and that you should use it as soon as possible after spills, because the longer a spill sits and dries, the harder it is to remove. 13
Think of it as a gentle first step, not a deep clean. The cycle makes steam inside the cavity, and you wipe the softened soil away afterward. It is meant for small spills such as cheese or sauce from a pizza or snacks, or drips from casseroles. 1
On a range, JennAir states that the function is designed for the light oven cavity bottom. 2 So it is not the tool for thick, baked-on soil on the whole cavity.
It is also not the same as a self-clean or AquaLift cycle. Those have their own help pages, and this guide covers only Steam Clean.
Which models have Steam Clean, and does it work the same way?#
JennAir describes two versions. The range version and the steam oven version share the name and the rules, but the setup differs. 12
| Range (Steam Clean) | Steam oven (Steam Cleaning) | |
|---|---|---|
| Water | Pour 12 oz (355 mL) of distilled or filtered water onto the oven bottom | Follow the on-screen instructions for the water container |
| Length | 50 minutes in total | Not stated on the help page |
| Start | Press the Steam Clean control | ON/HOME, Maintenance, Steam Cleaning, OK, then START |
| Cool-down | Must be at room temperature; HOT shows above 170°F (77°C) | Not stated on the help page |
| Racks | Remove all racks and accessories | Remove the wire shelf and trays |
| Source | 2 | 13 |
Check your own display and owner's manual for the exact keys on your model.
How do I run Steam Clean on a range?#
Let the range cool, take everything out, add the water and start the cycle. JennAir says the whole cycle takes 50 minutes, and End shows on the display when it finishes. 2
- 1
- 2
- 3
- 4
- 5
Do not use oven cleaners or any other additives with Steam Clean. 2 That includes spraying a cleaner in first to "help". JennAir also warns that foods react with porcelain at high temperatures, which can leave staining, etching, pitting or faint white spots, so spills should be wiped up once the oven cools. 4
How do I run Steam Cleaning on a steam oven?#
Take out the wire shelf and trays, close the door, press ON/HOME, scroll to Maintenance, choose Steam Cleaning, follow the on-screen instructions and press START. You can press CANCEL at any time. Keep the door shut while it runs. 13
JennAir's page uses the name Steam Cleaning for this function, and it is one of four Maintenance functions on a steam oven: Calibrate, Drain, Descale and Steam Cleaning. 1 Steam Cleaning is the one that rinses the oven. 1
On these models, the water in the oven bottom is hot, so the door stays shut until the cycle is done. 1 Use of oven cleaners or additives is not allowed here either. 1
What do I do after the cycle?#
Remove the water and the debris, wipe the moisture, and scrub where you need to. JennAir says to clear the remaining water and debris from the bottom of the oven with a sponge or cloth, and to wipe the oven door interior and the sides of the cavity dry. 13
- Use a soft brush or nylon scrubber on stubborn stains. 13
- If soil remains, run a second Steam Cleaning cycle to help loosen it. 13
- Food spills with sugar, protein or starch may still need vigorous scrubbing. 13
For routine cleaning, JennAir recommends warm water, mild detergent and a soft cloth for routine spills. For deeper cleaning it names a nonabrasive scrub sponge or an eraser-style pad without cleaners. 4

Why is there a ring on the oven bottom after Steam Clean?#
It is likely mineral deposits. JennAir explains that tap, spring and even filtered water contain dissolved minerals that stay behind after the water evaporates and can leave a ring. A reddish hint is typically rust in the water supply. 5
The ring can usually be removed by wetting the surface with a non-scratch sponge. If it stays, a 50/50 mix of vinegar and water will remove it, and you must wash the surface well with pure or distilled water afterward to prevent damage to the oven coating. 5
That is why the range version of Steam Clean calls for distilled or filtered water. 2 A little less mineral content in the water means a little less to wipe away.
When does Steam Clean point to a repair?#
When the function will not run on a cool oven, the display shows an error, water leaks out, or a steam oven keeps showing water messages after you follow the prompts. That suggests a failed part and not cleaning technique.
The other cleaning cycles are covered on the self-clean problems page, read about the oven water system on a steam oven, or visit our oven service page.
Sources#
- Using the Steam Clean Function - Product Help | JennAirJennAir Product Help (producthelp.jennair.com) · dateModified 2025-10-16; PH 704 · PH 704
- Steam Cleaning the Oven - Product Help | JennAirJennAir Product Help (producthelp.jennair.com) · dateModified 2024-08-27; PH 12758 · PH 12758
- Interior or Cavity - Wall Oven - Product Help | JennAirJennAir Product Help (producthelp.jennair.com) · dateModified 2025-02-17; PH 13433 · PH 13433
- Routine Oven Cleaning - Range - Product Help | JennAirJennAir Product Help (producthelp.jennair.com) · dateModified 2025-02-12; PH 12757 · PH 12757
- Cleaning Mineral Deposits on Oven Bottom - Product Help | JennAirJennAir Product Help (producthelp.jennair.com) · dateModified 2024-08-27; PH 13013 · PH 13013





