Before work starts
Before any work begins, the technician tells you what is needed and settles the cost with you. A built-in appliance may need to be examined on site before that figure is firm.
Independent appliance repair
JennAir rangetops and cooktops, whether gas, radiant electric or induction, come to us when a burner will not light, clicks without a flame, cycles oddly or the whole surface is dead. Name the fuel and the symptom, then book a technician.


Clicking with no flame points to a short list: Control Lockout after a power loss, a closed gas shut-off, a knob not turned to Ignite, moisture, or clogged ports. On a first start JennAir says to turn one knob for a moment so air leaves the line.

For a cooktop that does nothing, JennAir starts with the controls, the control or cooktop lock, the cord and the breaker. On an electric cooktop, turn the breaker off for one minute and back on. On a gas cooktop, also confirm that gas reaches it and the shut-off valve stands open.
No further researched dishwasher code is attached to this topic. Compare your exact message with your model manual and do not stand in a different code from the library.
See the research statusWe have not read a full Product Help library for this appliance, so we promise no part and no price in advance. The technician diagnoses on site and agrees the work with you first.

This component has no illustrated glossary entry on the site. Lean on the system described in the text and the model manual cited; a code by itself does not point to a replacement.
Explore the researched partsWhat happens on a visit.
No surprises in your kitchen.

Tell us which appliance, what the display shows and where it is installed. A photo of the model plate helps.

The technician inspects the unit, explains the likely cause and agrees the cost with you before starting.

When the work is done, the technician tests the appliance and walks you through what was fixed.
On gas, JennAir says to confirm the main shut-off is open. A handle parallel to the pipe means gas flows. Be careful with a flexible supply line; do not kink it.
After a power failure or unplugging, some gas cooktops come up in Control Lockout and burners will not light until it is cleared. The key press is typically held for three seconds.
On a recent installation, turn a burner on briefly to release trapped air in the gas line before expecting a flame.
Gas cooktops need a grounded outlet on their own circuit, and a tripped breaker or blown fuse stops the igniters. An electric cooktop page asks about its power cord, breaker and control lock.
JennAir says radiant elements cycle on and off by design, even at HI, and the surface can stay hot after they switch off.
Book us if burners click without lighting after the lockout and valve checks.
Book us if one burner works and the others do not.
Book us if the cooktop is dead on a circuit that has power.
If you smell gas, leave the home and call your gas utility or 911. Do not use switches or flames.
Arrange a diagnosticBefore any work begins, the technician tells you what is needed and settles the cost with you. A built-in appliance may need to be examined on site before that figure is firm.
If JennAir's manufacturer warranty covers the repair, JennAir itself does the work. We back our own workmanship with a warranty.
JennAir lists a Control Lockout after a power loss, a first-use air purge, clogged burner ports and a closed gas valve. Check the lockout first.
Yes. JennAir says radiant elements cycle on and off, including at HI, to protect the ceramic surface.
Yes. Give us the cooktop type, the model and the symptom, and the technician works out the cause when they arrive.
On the electronic ignition models JennAir describes, the burners will not light in a power failure when a lockout feature is present.
A cooktop still under the maker’s warranty is repaired through the maker. Otherwise the technician diagnoses, quotes and waits for your go-ahead.
Code or symptom, part, service call
Clicking with no flame points to a short list: Control Lockout after a power loss, a closed gas shut-off, a knob not turned to Ignite, moisture, or clogged ports. On a first start JennAir says to turn one knob for a moment so air leaves the line.
Schedule a diagnostic for your model, carried out at the appliance.
Office details, plus the access notes to pass along.