Start from the symptom
JennAir cooktop not powering on or nothing works.
For a cooktop that does nothing, JennAir starts with the controls, the control or cooktop lock, the cord and the breaker. On an electric cooktop, turn the breaker off for one minute and back on. On a gas cooktop, also confirm that gas reaches it and the shut-off valve stands open.

Start with safe observations.
Turn the appliance off and unplug it before any check you can do yourself. Look out for pooled water and sharp edges. Never touch a wet plug or live area, take off service panels, or go past your model’s owner instructions.
- 1
Confirm the controls are set
Refer to the owner's manual for the detailed control operation instructions for your model.
- 2
Look for the lock
The Control Lock avoids unintended use of the cooktop and oven. On a gas cooktop the Cooktop Lock makes the igniter spark and click while the burner will not light.
- 3
Check the cord and breaker
Plug the cord into a grounded outlet on a dedicated circuit. JennAir lists a 240V receptacle for electric ranges and cooktops and 120V for gas cooktops. Reset the tripped breaker or install a new fuse.
- 4
Reset the power
Turn the circuit breaker off for one minute, turn it back on and check that the cooktop operates.
- 5
Gas: check the supply
On a new install, turn one burner knob for a moment so air leaves the gas line, and verify the main gas valve is ON.
- 6
Know the power-failure rule
If the cooktop has a lockout, the surface burners will not light during a power failure.
More about this symptom.
What does the Control Lock do?#
It prevents unintended use of the cooktop and oven on touch-control models. If a cooktop seems dead, check for the lock before anything else, and use the unlock steps in the owner's manual.
What changes between electric and gas?#
Electric cooktops need the right 240V supply. Gas cooktops need a 120V outlet for the igniters, and the main gas valve ON. The lock and breaker checks apply to both.
What happens if none of this helps?#
When the lock is off, the breaker and cord are good, and the one-minute power reset changes nothing. Do not open the cooktop or work on its wiring yourself.
Systems a technician may investigate.
The symptom connects to these parts. What you observed cannot show that any single one has failed.

Main gas shut-off valve
The main gas shut-off valve feeds the cooktop. JennAir says to confirm it is ON if the cooktop does not work. With a lever ball valve, the handle in line with the pipe means gas flows, and across the pipe means it is cut off.

Surface burner igniter
JennAir cooktops light with electronic igniters, not standing pilots. Push the knob in and turn it counterclockwise to Ignite, wait for the flame, then set Hi to Lo. Some models re-ignite a burner that goes out, and a downdraft can make them keep sparking.
If the display adds a code.
When observation becomes a service request.
Leave internal testing to a technician.
The breaker trips again after a reset.
The cooktop stays dead with the breaker on, the cord in and the lock off.
The cooktop was just installed and never worked.
You smell gas.
Arrange a diagnosticSources and model boundaries.
The JennAir cooktop not powering on or nothing works guidance rests on these references. Pick the manual that fits your model.
- Not Powering On - Electric Cooktop - Product Help | JennAir
- Nothing Will Work - Gas Cooktop - Product Help | JennAir
Go by the instructions for your own model. See how we research these pages.
What should I check when my JennAir cooktop shows nothing?
The controls, then the control lock on touch models, then the cord and the household breaker or fuse. After that, a one-minute power reset at the breaker.
How do I reset the power on a cooktop?
Turn off the circuit breaker for one minute, turn it back on, and check that the cooktop operates. JennAir gives this as the standard reset for electric cooktops.
Why does my gas cooktop spark but not light?
If the Cooktop Lock is on, you will hear clicking and may see the igniter spark, but the burner will not light. Release the lock using the owner's manual steps.
What outlet does the cooktop need?
JennAir lists a grounded, three-prong outlet on a dedicated circuit for gas cooktops (120V) and a 240V receptacle for electric. If the breaker keeps tripping, call an electrician.
Is a dead cooktop dangerous?
Not by itself. On a gas cooktop, any gas smell means you go outside and phone the gas company. Otherwise run the checks, and book a technician if power and lock are fine.
Code or symptom, part, service call
Tie the message to what comes next.
Cooktop Lock
Cooktop Lock on a JennAir range means the control lock for the surface cooking areas is on. JennAir describes it as protection against unintended use. Touch and hold LOCK for three seconds to turn it off.
JennAir gas cooktop burner clicks but will not light
Clicking with no flame points to a short list: Control Lockout after a power loss, a closed gas shut-off, a knob not turned to Ignite, moisture, or clogged ports. On a first start JennAir says to turn one knob for a moment so air leaves the line.
Main gas shut-off valve
The main gas shut-off valve feeds the cooktop. JennAir says to confirm it is ON if the cooktop does not work. With a lever ball valve, the handle in line with the pipe means gas flows, and across the pipe means it is cut off.
Cooktop repair
Schedule a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, plus the access notes to pass along.