Before work starts
Before any work begins, the technician tells you what is needed and settles the cost with you. A built-in appliance may need to be examined on site before that figure is firm.
Independent appliance repair
JennAir built-in, drawer and over-the-range microwaves come to us when they will not heat, will not start or show a code. Name the type and the display message, then book a technician.


First confirm the controls: enter Cook Time, then Cook Power if it is not 100%, and press Start. Then test with one cup of water for one minute on HI. If heat rise is detected, the microwave is heating. With no power at all, check the breaker or fuse.

A microwave that has power but will not start is usually blocked by the door, the Control Lock, Demo Mode or a blank Energy Save display. Confirm that nothing stops the door shutting, check the lock, then switch the breaker off for a minute.
No further researched dishwasher code is attached to this topic. Compare your exact message with your model manual and do not stand in a different code from the library.
See the research statusWe have not read a full Product Help library for this appliance, so we promise no part and no price in advance. The technician diagnoses on site and agrees the work with you first.

This component has no illustrated glossary entry on the site. Lean on the system described in the text and the model manual cited; a code by itself does not point to a replacement.
Explore the researched partsWhat happens on a visit.
No surprises in your kitchen.

Tell us which appliance, what the display shows and where it is installed. A photo of the model plate helps.

The technician inspects the unit, explains the likely cause and agrees the cost with you before starting.

When the work is done, the technician tests the appliance and walks you through what was fixed.
The built-in page tests heating with one cup of water for one minute on HI. If the water warms, the microwave is heating and the setting was the issue.
Shipping material, an oversized dish or a rack out of position can stop the door latching. A blank display may be Energy Save mode rather than a failure.
Control Lock, a running kitchen timer and Demo Mode all stop the microwave from starting while the display is still alive.
For no power at all, reset a tripped breaker or replace a blown fuse. If it trips again, a licensed electrician looks at the circuit.
Over-the-range microwaves have a library of F pages. F1E1 names the relay control board and wiring, with a one-minute breaker reset.
Book us if the water test shows no heat with the right power level.
Book us for an F code that returns after the one-minute reset.
Book us if the door is bent, will not latch or the cabinet is damaged.
Book us for sparks, arcing or a burning smell.
Arrange a diagnosticBefore any work begins, the technician tells you what is needed and settles the cost with you. A built-in appliance may need to be examined on site before that figure is firm.
If JennAir's manufacturer warranty covers the repair, JennAir itself does the work. We back our own workmanship with a warranty.
Built-in, microwave drawer and over-the-range models. Put the model in your booking so the technician knows which type.
The built-in page says Energy Save mode blanks the display when idle on select models. If it stays blank when you press a key, check the breaker.
The page says the oven could not execute the function, with a possible problem in the relay control board or wiring. It asks for a one-minute breaker reset.
Please don’t. Internal microwave parts hold high voltage even when unplugged, so leave the cabinet to a technician.
A microwave still covered by the manufacturer’s warranty is the manufacturer’s to fix. If yours is out of coverage, you get a quote after the diagnostic and choose whether to proceed.
Code or symptom, part, service call
First confirm the controls: enter Cook Time, then Cook Power if it is not 100%, and press Start. Then test with one cup of water for one minute on HI. If heat rise is detected, the microwave is heating. With no power at all, check the breaker or fuse.
Schedule a diagnostic for your model, carried out at the appliance.
Office details, plus the access notes to pass along.