Start from the symptom
JennAir microwave built-in microwave not heating.
First confirm the controls: enter Cook Time, then Cook Power if it is not 100%, and press Start. Then test with one cup of water for one minute on HI. If heat rise is detected, the microwave is heating. With no power at all, check the breaker or fuse.

Start with safe observations.
Turn the appliance off and unplug it before any check you can do yourself. Look out for pooled water and sharp edges. Never touch a wet plug or live area, take off service panels, or go past your model’s owner instructions.
- 1
Set Cook Time
Touch COOK TIME and enter the time on the number pads.
- 2
Set Cook Power
Touch COOK POWER if it is not 100%, and enter a level from 10 to 90.
- 3
Touch Start
The oven does not run until Start is pressed.
- 4
Run the water test
Place one cup (250 mL) of water on the turntable and run it one minute at HI, 100% power. If heat rise is detected, the microwave is heating.
- 5
No power at all?
Check that no household fuse has blown and no breaker has tripped. Reset the breaker or swap the fuse. If it keeps happening, call a licensed electrician.
More about this symptom.
What does JennAir list for a microwave that is not heating?#
Controls set correctly for Cook Time and Power Level, and a water test: one cup for one minute at HI. A heat rise means the microwave is heating.
What if there is no power?#
Check the fuse or breaker first. JennAir's article for a unit that is not operating lists only that check, then a licensed electrician if it continues.
Which repeat of the symptom means a repair?#
When the water stays cool after a correct test. The heating parts of a microwave carry high voltage and are not for owners to open.
Systems a technician may investigate.
The symptom connects to these parts. What you observed cannot show that any single one has failed.

Microwave relay control board
The relay control board switches the microwave’s functions. JennAir’s F1E1 page for over-the-range microwaves says the oven could not execute the function and names the relay control board or its wiring as the possible problem.

Microwave control lock
The Control Lock turns off the control panel pads so the microwave cannot be started by accident. JennAir lists it for both a start button that does nothing and a microwave that has power but will not run.
If the display adds a code.
No code tied directly to this topic.
No further researched dishwasher code is attached to this topic. Compare your exact message with your model manual and do not stand in a different code from the library.
See the research statusFollow the care instructions written for this appliance.
When observation becomes a service request.
Leave internal testing to a technician.
The cup of water stays cool after a minute on HI.
The microwave runs, the light and fan work, but food stays cold.
The breaker trips when you start the microwave.
The display is on and the unit does not start.
Arrange a diagnosticSources and model boundaries.
The JennAir built-in microwave not heating guidance rests on these references. Pick the manual that fits your model.
- Not Heating - Built-In Microwave - Product Help | JennAir
- No Power - Not Operating - Built-In Microwave - Product Help | JennAir
Go by the instructions for your own model. See how we research these pages.
What is the simple heating test?
Place one cup (250 mL) of water on the turntable and run it one minute on the HI setting at 100% power. If a heat rise is detected, the microwave is heating.
Could my power level be the reason?
Yes. If Cook Power was set below 100%, food heats slowly. JennAir's manual steps enter a power level from 10 to 90 after Cook Time, before Start.
What if the microwave has no power?
Look for a blown household fuse or a tripped breaker. Reset the breaker or swap the fuse. If the trouble continues, JennAir says to bring in a licensed electrician.
Is it safe to run a microwave that does not heat?
Running it empty is not safe for the microwave. Always put the cup of water in for the test. If water stays cool, stop using it and book a technician.
Does a working light and fan mean the oven heats?
No. The light, fan and turntable can run while the magnetron does not heat. Demo Mode also lets functions run without heating, so confirm the mode before you call.
Code or symptom, part, service call
Tie the message to what comes next.
JennAir built-in microwave not heating
First confirm the controls: enter Cook Time, then Cook Power if it is not 100%, and press Start. Then test with one cup of water for one minute on HI. If heat rise is detected, the microwave is heating. With no power at all, check the breaker or fuse.
Microwave control lock
The Control Lock turns off the control panel pads so the microwave cannot be started by accident. JennAir lists it for both a start button that does nothing and a microwave that has power but will not run.
Microwave repair
Schedule a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, plus the access notes to pass along.