What it means
F3E2 on a JennAir dishwasher lists a thermistor or an OWI sensor as the potential cause, both sensing parts. JennAir's answer is a thirty-second power loss, with service as the next step.
JennAir dishwasher F3E2 / Sensors
F3E2 on a JennAir dishwasher lists a thermistor or an OWI sensor as the potential cause, both sensing parts. JennAir's answer is a thirty-second power loss, with service as the next step.
Also shown as F3E2
F3E2 on a JennAir dishwasher lists a thermistor or an OWI sensor as the potential cause, both sensing parts. JennAir's answer is a thirty-second power loss, with service as the next step.
If water or dishes are still hot, wait.
F3E2 returns after the reset.
Checks you have ticked / saved in this browser

If water or dishes are still hot, wait. Sensors can be affected by a mid-cycle stop, and the tub holds hot water.

Disconnect the dishwasher from the outlet or its breaker, count thirty seconds, and then reconnect it.

Start the shortest program with the door latched. Watch the display for F3E2 during the first few minutes.

Record when F3E2 appeared: right at power-up, while heating, or near the end. That timing helps a technician choose where to look.
Send the model and the checks you have already run, then begin your request from this page.
Book a visit
A simplified drawing, because layouts change with the model. Tap an outlined part to see a photo and the related check.

Component reference
JennAir F3E2 names the thermistor or OWI sensor, the temperature and water sensing part.
Read the definitionThe page names both without explaining them. Generally, a thermistor is a temperature sensor and the OWI sensor, as JennAir names it, helps the control judge water conditions. We stay with the page's naming.
Read the supporting manualIt is the only step JennAir prints. If the control sets the code again after the reset, the sensor or its wiring is a likely place for a technician to look.
Read the supporting manualF4E2 is listed with the heating system and F4E3 as a heating error. F3E2 sits with sensors instead, so a hot-water problem alone does not explain it.
Read the supporting manualManufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2026-06-15; PH 12193 / PH 12193 (dishwasher)
JennAir dishwasher page PH 12193, last modified 2026-06-15.
JennAir does not list F3E3 on its dishwasher pages. Treat F3E2 as its own code and see the not-listed page for codes searchers use that JennAir does not print.
JennAir does not say. The page speaks about sensing parts, not about the incoming water temperature.
We do not advise it. The page offers no replacement steps, and the part sits inside the tub or base where wiring and water are close together.
The page does not say. A sensing error can stop the cycle or give poor results, so avoid running load after load until it is checked.
The code, the model number, what stage of the cycle it appeared in, and whether the power cycle helped for even a short time.
Code or symptom, part, service call
On JennAir's dishwasher page, F4E2 points to the heating system. The one step printed is thirty seconds without power; a repeat means service. The parts under the tub are for a technician only.
JennAir's order is power, then the door and lower rack, then water supply, control lock, delay start, and a one-minute reset. A dishwasher that will not fill adds the drain loop height and an interrupted-cycle flash to the list.
JennAir F3E2 names the thermistor or OWI sensor, the temperature and water sensing part. The page gives a power cycle and says to schedule service if the code returns. It is a good example of a code that names a part and gives the owner a single step.
Schedule a diagnostic for your model, carried out at the appliance.
Office details, plus the access notes to pass along.