What it means
JennAir lists F7E2 as a wash motor error. Remove power for thirty seconds; a repeat of F7E2 calls for a technician. The wash motor drives the circulation pump, so listen for a hum without water movement.
JennAir dishwasher F7E2 / Motor
JennAir lists F7E2 as a wash motor error. Remove power for thirty seconds; a repeat of F7E2 calls for a technician. The wash motor drives the circulation pump, so listen for a hum without water movement.
Also shown as F7E2
JennAir lists F7E2 as a wash motor error. Remove power for thirty seconds; a repeat of F7E2 calls for a technician. The wash motor drives the circulation pump, so listen for a hum without water movement.
Pull the plug or turn the breaker off.
F7E2 returns after the power cycle.
Checks you have ticked / saved in this browser

Pull the plug or turn the breaker off. A motor error is not something to test with the machine live.

Open the door and look for an item that has dropped to the bottom or blocks a spray arm. This is our own advice rather than a printed step.

Time it on a clock. Then close the door and start a short cycle.

A steady hum with no spray, or silence, is worth telling the technician. Write down what you hear.
Send the model and the checks you have already run, then begin your request from this page.
Book a visit
A simplified drawing, because layouts change with the model. Tap an outlined part to see a photo and the related check.

Component reference
The wash motor spins the circulation pump that pushes water to the spray arms.
Read the definitionIt spins the pump that sends water through the spray arms. JennAir blames it for F7E2 and offers just a power cycle before service.
Read the supporting manualNot reliably. A jam, a drained tub or a control issue can look similar. No test is given, so a technician should check.
Read the supporting manualThe page set for dishwashers lists F7E2 only; the oven F7 codes are different appliance tables. Keep them apart when you search online.
Read the supporting manualManufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2026-06-15; PH 12198 / PH 12198 (dishwasher)
Manufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2026-08-31; PH 14220 / PH 14220 (dishwasher)
JennAir dishwasher page PH 12198, last modified 2026-06-15; the overview page PH 14220 repeats the code.
No. F9E2 is listed as a drain motor error. F7E2 is the wash motor.
We would not push it. A motor that struggles can overheat, so stop after one reset attempt.
JennAir does not say. If the dishwasher sat unused for a long time, mention that when you book.
It may, since the motor may not circulate or drain. Check the tub and remove standing water by hand if safe.
The model number, the sound the machine made, and whether the reset made any difference.
Code or symptom, part, service call
F6E1 on a JennAir dishwasher is listed as User Interface Error, Main Control. The page asks you to cycle the power for 30 seconds and to schedule service if the code comes back. The Clean light flashes it as six flashes, a pause, then one.
JennAir's order is power, then the door and lower rack, then water supply, control lock, delay start, and a one-minute reset. A dishwasher that will not fill adds the drain loop height and an interrupted-cycle flash to the list.
The wash motor spins the circulation pump that pushes water to the spray arms. JennAir F7E2 reads "Wash Motor Error". The page gives one step, a power cycle, and says to schedule service if the code comes back.
Schedule a diagnostic for your model, carried out at the appliance.
Office details, plus the access notes to pass along.