What it means
JennAir's page for 3d31 has you check the meat probe is pushed all the way into its receptacle, and names no failed part. Try a one-minute breaker cycle, then look for the code for 60 seconds.
JennAir oven 3d31 / Meat probe
JennAir's page for 3d31 has you check the meat probe is pushed all the way into its receptacle, and names no failed part. Try a one-minute breaker cycle, then look for the code for 60 seconds.
Also shown as 3d31
JennAir's page for 3d31 has you check the meat probe is pushed all the way into its receptacle, and names no failed part. Try a one-minute breaker cycle, then look for the code for 60 seconds.
Give the racks and glass time to cool with 3d31 showing.
3d31 returns after the breaker reset.
Checks you have ticked / saved in this browser

Give the racks and glass time to cool with 3d31 showing.

With the oven off and cool, press the probe plug fully into the oven wall receptacle and wipe away residue first before 3d31 gets another chance.

Breaker off for a full minute, then on; look for 3d31 for another minute.

Copy 3d31 as displayed, and the cycle running at that moment.

Wipe the probe tip and socket with the oven off and cold; a film of fat can spoil the contact on 3d31.
Send the model and the checks you have already run, then begin your request from this page.
Book a visitA simplified drawing, because layouts change with the model. Tap an outlined part to see a photo and the related check.

Component reference
Several JennAir F3 and F8 codes come from the meat probe.
Read the definitionOn 3d31, JennAir says only to verify that the probe sits firmly in its receptacle, then resets power. No part is blamed.
Read the supporting manualJennAir's fix for 3d31 is a breaker reset for 60 seconds. Then watch the display.
Read the supporting manualOnce it behaves after the reset, light use is reasonable. A second 3d31 means stand down and book a visit.
Read the supporting manualOn the 3d32 row JennAir lists only a meat probe check; for 3d31 it lists the probe plug.
Read the supporting manualManufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2024-08-16; PH 12905 / PH 12905 (range)
Manufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2024-11-08; PH 13279 / PH 13279 (wall oven)
Applies to: freestanding range and wall oven. Basis: JennAir Product Help PH 12905, PH 13279. One printed line for 3d31, so our guidance is general.
The page asks you to verify the meat probe is seated in its receptacle. No failed part is named.
Cut the breaker for 60 seconds, then back on, then observe 3d31 a minute.
Hold off while 3d31 is up. Do the reset first, then cook if it heats normally.
Not by itself. JennAir only asks for seating; a worn cable is a separate matter.
Code or symptom, part, service call
On a range or wall oven, 3d32 is a prompt about the meat probe seat: JennAir blames no component. Try a 60-second power cycle, then watch for the code for 60 seconds.
JennAir says not to judge oven temperature with a thermometer, because the elements cycle and most thermometers react too slowly. Check preheat time, racks, pan spacing and foil first, then run the biscuit test before any calibration.
Several JennAir F3 and F8 codes come from the meat probe. The pages ask you to confirm the probe is seated in its receptacle, and on some wall ovens to check a power attachment on the roll-out rack. These are quick owner checks before any reset.
Schedule a diagnostic for your model, carried out at the appliance.
Office details, plus the access notes to pass along.