Read the whole display
Give the product type and the exact code, including any dash, space or letter after the F. The same string, such as F7 E0 or F9E0, names different parts on a range, a wall oven and a professional-style range.
Model-specific code library
We decode 198 oven codes and messages: the bare codes F1 to F5 and F9 as pages, F7 and FC as prefix pages, and 190 shorter rows, each tied to the product type that prints it (freestanding range, wall oven, professional-style range or steam oven).
F9 on a JennAir wall oven most often means the oven was wired wrongly at the home supply or the hard-wire connection, with L2 and N swapped as the example; a steam oven page gives only a reset. Call an electrician before using the oven again.
Read the F9 checks201 researched oven codes. Each model reads codes its own way, so go by your own manual.
4d11 says the door lock and switch or its wiring may need attention. Drop the breaker for 60 seconds, return power, and observe for the code.
Reset, then bookTreat 4d12 as a warning about the door latch assembly, with wiring as backup. Switch off the breaker for sixty seconds, return power, then monitor the code.
Reset, then book1c31 names the oven's control board or the wiring serving it on JennAir ranges and wall ovens. The first step is a sixty-second power reset at the breaker panel; call for service if it returns.
Reset, then bookRead 1c32 as a warning about the electronic control, wiring second. Cut the circuit breaker for 60 seconds, restore power, then watch the code.
Reset, then book1d11 starts JennAir's "Starts with 1d" group and lists the temperature sensor and the control, or the wiring between them. The first step is a sixty-second power reset at the breaker panel; call for service if it returns.
Reset, then bookJennAir ties 1d12 to the temperature sensor and the control, or the wiring between them. If the code comes back, book a technician. The first step is a sixty-second power reset at the breaker panel; call for service if it returns.
Reset, then book1c1c is the first row in JennAir's "Starts with 1c" group, and it is the one that names the touch panel (JennAir's user interface) or its wiring. The first step is a sixty-second power reset at the breaker panel; call for service if it returns.
Reset, then book1c2c says the touch controls or the wiring may need attention. Cycle the breaker once, a minute off; if the code returns, schedule a visit.
Reset, then bookF1E3 on a JennAir combination wall oven names the microwave appliance manager or its wiring. The page asks for a one-minute breaker reset: switch off, turn back on, then watch the oven for a minute to see whether the code returns.
Reset, then bookF1E4 on a JennAir combination wall oven names the microwave appliance manager, the microwave power relay or their wiring. Switch the breaker off for one minute, turn it on and watch the oven for one minute. If F1E4 comes back, book a technician.
Reset, then book4d21 means the cooling fan speed is too low, per JennAir. The pages name something restricting airflow, the cooling fan, or its wiring. Check the vents for blockage first, then run the sixty-second power reset at the breaker panel.
Reset, then book4d22 says the cooling fan speed is too low, on JennAir ranges and wall ovens. Check the vents for blockage first, then run the sixty-second power reset at the breaker panel.
Reset, then bookAmber lights that blink with three short tones and one longer tone mean a professional-style JennAir range has stored an error. Turn the Mode and Temp knobs to any new position, then set Mode to Bake and Temp to Off. If the amber lights return, the range needs a technician.
Reset, then bookIf a connected professional-style JennAir range is blinking its controls, the JennAir app can show why. Open the app, go to Settings, then Service and Support, then Appliance Error. The range must be registered in the app first.
Information onlyA C on a JennAir oven display means the temperature scale is set to Celsius. JennAir's cooking appliance chart lists it as a display setting, not an error. While the oven reads in Celsius a 260 limit applies on the display, so nothing is broken when you see it.
Information onlyCAL on a JennAir oven display is the calibration feature, not an error. JennAir's cooking appliance chart describes it as the function that lets you adjust the oven temperature. Read your owner's manual before changing anything, because a bad offset makes every bake run off.
Information onlyF4 E1 names the thermistor, the appliance manager or the wiring on a JennAir wall oven; the page does not specify which cavity. Reset at the breaker for sixty seconds and watch for a minute.
Reset, then bookF6 E0 asks for a reset on a professional-style range and a wall oven, and names the oven control, appliance manager or wiring on a freestanding range. Cycle power for the time your page gives.
Reset, then bookC81 means a surface cooking area on a JennAir range overheated and the automatic shutoff tripped. Turn the oven off if it is running, wait five minutes for the cooktop to cool, then turn it back on. If C81 shows again, switch the breaker off for one minute.
Owner checks firstC82 is the same JennAir cooktop warning as C81: a surface cooking area ran too hot and the range shut it down. Turn off the oven if it is on, give the cooktop five minutes, then try it again. Reset the breaker for a minute if C82 comes back.
Owner checks firstCall Service on a JennAir oven means the control detected an error. Press Cancel first. If the message stays, switch the breaker off for one minute, turn it back on, start a bake cycle and watch the oven for a minute. If it returns, book a technician.
Reset, then bookFeature Not Available or Fault Detected scrolls across a JennAir range or wall oven display when the control found an error while you were setting a cook cycle. Follow the text on screen, then reset power at the breaker for 60 seconds.
Reset, then bookJennAir's page for 3d31 has you check the meat probe is pushed all the way into its receptacle, and names no failed part. Try a one-minute breaker cycle, then look for the code for 60 seconds.
Owner checks firstOn a range or wall oven, 3d32 is a prompt about the meat probe seat: JennAir blames no component. Try a 60-second power cycle, then watch for the code for 60 seconds.
Owner checks firstF13 on a JennAir steam wall oven comes with a reset only, and no cause is printed. Switch the oven breaker off for one minute, turn it back on, start a cycle and watch the oven for a minute. If F13 returns, book a technician.
Reset, then bookF7 E2 gives a reset only, on a JennAir professional-style range and on a wall oven; neither page names a part. Turn the knob to OFF on a pro range, or cycle the breaker for about a minute on a wall oven.
Reset, then bookJennAir prints no bare FC. FC E1 to E9 are connected-appliance codes on ranges and wall ovens: E1 to E3 and E7 say the oven could not reach your router, E4 and E5 name the Wi-Fi antenna, E6 and E9 the Wi-Fi power module, and E8 is a registration entry error. Start with the home network.
Owner checks firstFC E1 on a JennAir range or wall oven means the appliance could not connect to your router, with poor signal, a failed router, the Wi-Fi module or its wiring as possible causes. Restart the router and the oven, then check the signal at the oven.
Owner checks firstDescale is needed on a JennAir steam oven means it is time to clean and descale it. From the Maintenance menu choose Descaling and follow the on-screen steps. The page lists 34 oz of water mixed with 8.5 oz of descaler or white vinegar, and the cycle must run to the end.
Information onlyEmpty and Refill Water Container is a reminder on a JennAir steam oven, shown before each steam cycle starts. Open the door, empty the container, fill it with fresh tap or still bottled water to the MAX mark, seat it firmly, close the door and restart or press START.
Information onlyPlease Remove and Empty Container appears on a JennAir steam wall oven at the end of the Drain cycle. Empty the water container, put it back in its compartment and press OK.
Information onlyTemperature Reached Insert Food on a JennAir steam wall oven means preheating is finished and the set temperature has been reached. Open the door carefully and put the food in.
Information onlyFC E4 names the Wi-Fi antenna or its wiring on a JennAir range or wall oven. Reset the breaker for sixty seconds; if the code returns, the problem is inside the oven and needs a technician.
Reset, then bookFC E5 repeats the Wi-Fi antenna wording of FC E4 on a JennAir range or wall oven. Reset the breaker for about a minute and, if the code returns, plan a technician visit; the router is not the cause.
Reset, then bookFC E6 names the Wi-Fi power module or its wiring on a JennAir range or wall oven. Reset the breaker for 60 seconds; if the code returns, the module needs a technician.
Reset, then bookFC E9 repeats the Wi-Fi power module wording of E6 on a JennAir range or wall oven. Reset the breaker for about a minute; if the code returns, the module or its wiring needs a technician and the router is not the cause.
Reset, then bookF7 E3 appears only on JennAir wall ovens, where the page names the water filter. Check the filter is seated and not overdue, then cycle the breaker for about a minute.
Reset, then bookF7 E4 names the water conductivity sensor or its wiring on a JennAir wall oven. Cycle the breaker for about a minute and, if your oven has a water reservoir, check it holds clean water as your manual describes.
Reset, then bookF9 on a JennAir wall oven most often means the oven was wired wrongly at the home supply or the hard-wire connection, with L2 and N swapped as the example; a steam oven page gives only a reset. Call an electrician before using the oven again.
Electrician firstF9 E0 on a JennAir professional-style range or wall oven points at the electrical supply: the pro-range pages ask for the outlet or supply to be checked, and the wall oven page names wrong wiring at the supply with L2 and N swapped as the example. Have an electrician check before further use.
Electrician firstFC E8 is a registration entry error on a JennAir range or wall oven: the SAID number or the appliance type and model may have been entered wrongly. Enter them again carefully.
Owner checks firstRegistration Error on a JennAir combination wall oven means linking the oven to the connected-appliance service failed. Work down JennAir's list: home internet, firewall, the oven joined to the network, a previous owner, the SAID number, and the appliance type and model.
Owner checks firstFEE6 on a JennAir freestanding range names the main cavity bake element or its wiring. Let the oven cool, reset the breaker for about a minute and see whether the range still heats from the bottom.
Reset, then bookFEE7 on a JennAir freestanding range names the main cavity broil element or its wiring. Let the oven cool, reset the breaker for about a minute and test with a short broil only if the oven otherwise behaves.
Reset, then bookCooktop, microwave, coffee machine and undercounter codes have their own JennAir code libraries. FR and a bare F are printed nowhere. FBE1, FBE2, FEE8, F13 and F7E2 name no cause, only a reset.

We decode 198 oven codes and messages: the bare codes F1 to F5 and F9 as pages, F7 and FC as prefix pages, and 190 shorter rows, each tied to the product type that prints it (freestanding range, wall oven, professional-style range or steam oven).
Cooktop, microwave, coffee machine and undercounter codes have their own JennAir code libraries. FR and a bare F are printed nowhere. FBE1, FBE2, FEE8, F13 and F7E2 name no cause, only a reset.
Give the product type and the exact code, including any dash, space or letter after the F. The same string, such as F7 E0 or F9E0, names different parts on a range, a wall oven and a professional-style range.
Ovens run on household voltage and may be hard-wired. Switch the breaker off before anything beyond a reset, and leave supply wiring to a qualified electrician. If you smell gas, leave and call your gas supplier from outside.
JennAir says not to judge oven temperature with a thermometer, because the elements cycle and most thermometers react too slowly. Check preheat time, racks, pan spacing and foil first, then run the biscuit test before any calibration.
Find your cooktop type first. Glowing that cycles on and off is normal on electric coil and glass tops, and gas flame trouble starts with clean ports and a seated cap. LP conversion or a wrong gas type needs a technician.
Most JennAir door complaints trace to something blocking the latch, a rack or pan that is not seated, or a door put back on wrong. Moisture on the glass and a rainbow tint are listed as normal and need no repair.
Go by the instructions for your own model. See how we research these pages.
Cooktop, microwave, coffee machine and undercounter codes have their own JennAir code libraries. FR and a bare F are printed nowhere. FBE1, FBE2, FEE8, F13 and F7E2 name no cause, only a reset.
Take a clear photo of the whole oven display and of the model label. Add what the appliance was doing when the message came up, and do not borrow the explanation for a different appliance.
An old search phrase is no substitute for manufacturer evidence. When our oven documents leave a message undecoded, we show the name only and send you toward help, with no part or cause attached.
Browse the manufacturer documents in this oven library and hold the models on their covers up against your label. Another model needs instructions of its own.