What it means
JennAir's page for 3d41 asks you to confirm the meat probe is fully seated in its receptacle; it names no part at all. Try a 60-second breaker cycle, then look for the code for a minute.
JennAir oven 3d41 / Meat probe
JennAir's page for 3d41 asks you to confirm the meat probe is fully seated in its receptacle; it names no part at all. Try a 60-second breaker cycle, then look for the code for a minute.
Also shown as 3d41
JennAir's page for 3d41 asks you to confirm the meat probe is fully seated in its receptacle; it names no part at all. Try a 60-second breaker cycle, then look for the code for a minute.
Touch nothing hot before you handle 3d41.
3d41 returns after the breaker reset.
Checks you have ticked / saved in this browser

Touch nothing hot before you handle 3d41.

When the oven is cold, push the probe plug all the way into its receptacle and wipe away residue first before 3d41 gets another chance.

Breaker off for a full minute, then on; watch for 3d41 one more minute.

Jot down 3d41 as displayed, and the cycle running at that moment.

Seat it a second time with the oven off until it seats fully, then retry after 3d41.
Send the model and the checks you have already run, then begin your request from this page.
Book a visitA simplified drawing, because layouts change with the model. Tap an outlined part to see a photo and the related check.

Component reference
Several JennAir F3 and F8 codes come from the meat probe.
Read the definitionThe entry for 3d41 is a check, not a diagnosis: seat the probe, cycle the breaker. No part is named.
Read the supporting manualJennAir's fix for 3d41 is a breaker reset for one minute. Then monitor the display.
Read the supporting manualCarry on only if the oven heats evenly after the breaker cycle. A returning 3d41 is a reason to book a technician.
Read the supporting manual3d51 names the main control; 3d41 names the probe seating. Go by your own display.
Read the supporting manualManufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2024-08-16; PH 12907 / PH 12907 (range)
Manufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2024-11-08; PH 13281 / PH 13281 (wall oven)
Appliances covered: freestanding range and wall oven. Source: JennAir Product Help PH 12907, PH 13281. JennAir prints little for 3d41, so the rest is our guidance.
JennAir asks you to verify the meat probe is seated in its receptacle. It names no part.
Breaker off for a minute, then back on, then watch 3d41 for 60 seconds.
Hold off while 3d41 is up. Reset, then judge, then cook only if it behaves.
Not necessarily. JennAir only asks for seating; a damaged cable is a separate matter.
Code or symptom, part, service call
3d51 names the oven's control board or the wiring serving it. The first step is a sixty-second power reset at the breaker panel; call for service if it returns.
JennAir says not to judge oven temperature with a thermometer, because the elements cycle and most thermometers react too slowly. Check preheat time, racks, pan spacing and foil first, then run the biscuit test before any calibration.
Several JennAir F3 and F8 codes come from the meat probe. The pages ask you to confirm the probe is seated in its receptacle, and on some wall ovens to check a power attachment on the roll-out rack. These are quick owner checks before any reset.
Schedule a diagnostic for your model, carried out at the appliance.
Office details, plus the access notes to pass along.