What it means
4d52 names the latch assembly and the switch on the door, or the wiring to them. The first step is a sixty-second power reset at the breaker panel; call for service if it returns.
JennAir oven 4d52 / Door latch and switch
4d52 names the latch assembly and the switch on the door, or the wiring to them. The first step is a sixty-second power reset at the breaker panel; call for service if it returns.
Also shown as 4d52
4d52 names the latch assembly and the switch on the door, or the wiring to them. The first step is a sixty-second power reset at the breaker panel; call for service if it returns.
If it was running, let it cool.
4d52 comes back after the one-minute breaker reset.
Checks you have ticked / saved in this browser

If it was running, let it cool. Do not force a latched door; the reset is at the breaker panel.

Check that a rack, pan or foil is not keeping the door from closing fully. That is our check, not JennAir's.

Find the oven's circuit breaker, leave it off for sixty seconds, flip it on, and keep an eye on the display for a minute.

After the reset, notice whether the door closes fully and whether the lock engages when it should. Tell the technician what you saw.
Send the model and the checks you have already run, then begin your request from this page.
Book a visit
A simplified drawing, because layouts change with the model. Tap an outlined part to see a photo and the related check.

Component reference
The latch assembly and its door switch lock the oven door for self-clean and report that the door is closed.
Read the definitionJennAir's range (PH 12918) and wall-oven (PH 13292) pages list the latch assembly and the switch on the door, or the wiring to them as the possible problem. It does not say which part is responsible, and it names no repair.
Read the supporting manualLet the oven cool, make sure nothing keeps the door from closing, then run the sixty-second power reset at the breaker panel and keep an eye on the display for a minute. Do not pry a stuck door.
Read the supporting manualThe next row is 9d11, which reads the same way. JennAir switches from a 4d to a 9d prefix without explaining it, so 4d52 is the last of the 4d door rows, not a different problem.
Read the supporting manualIf the reset clears it and the door closes and locks normally, ordinary cooking is reasonable. If the code returns, or the door will not close or open as it should, stop and call for service.
Read the supporting manualManufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2024-08-16; PH 12918 / PH 12918 (range)
Manufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2024-11-08; PH 13292 / PH 13292 (wall oven)
Applies to: freestanding range and wall oven. Source: JennAir Product Help PH 12918, PH 13292. The pages print one cause line and the reset; everything else here is our guidance.
Let the oven cool, make sure nothing blocks the door, then run the sixty-second power reset at the breaker panel and watch the display.
JennAir does not address it, so do not pry the door. Let the oven cool and do the breaker reset first.
Not by itself. The page names the latch assembly and the switch on the door, together with the wiring to them as possible problems; a technician has to test them.
The cause list is identical. JennAir files them under different prefixes and gives no reason.
Code or symptom, part, service call
9d11 opens the 9d group and lists the latch assembly and the switch on the door, or the wiring to them. The first step is a sixty-second power reset at the breaker panel; call for service if it returns.
JennAir says not to judge oven temperature with a thermometer, because the elements cycle and most thermometers react too slowly. Check preheat time, racks, pan spacing and foil first, then run the biscuit test before any calibration.
The latch assembly and its door switch lock the oven door for self-clean and report that the door is closed. JennAir lists them for F5 codes and F7 E0, and for the locked-door and door-will-not-close pages. A bent latch arm is one check you can do yourself.
Schedule a diagnostic for your model, carried out at the appliance.
Office details, plus the access notes to pass along.