Inside the appliance
Bake and broil elements. In plain English.
On JennAir ranges, FEE6 names the main cavity bake element and FEE7 the main cavity broil element, each with its wiring. The pages offer one owner step: a one-minute breaker reset. An element that stays cold afterwards needs a technician with the power off.

Where it fits.
Bake and broil elements in the appliance
Bake element along the cavity floor or beneath it, broil element across the cavity ceiling. Layout varies by model.
The picture shows the kind of component only. It cannot tell you which replacement suits your model.
What you notice when this system needs a look.
A Bake and broil elements concern may show up with a drop in performance or a code that keeps returning. Testing comes first, before anyone decides the component is to blame.

JennAir oven temperature problems
JennAir says not to judge oven temperature with a thermometer, because the elements cycle and most thermometers react too slowly. Check preheat time, racks, pan spacing and foil first, then run the biscuit test before any calibration.

JennAir range burner problems
Find your cooktop type first. Glowing that cycles on and off is normal on electric coil and glass tops, and gas flame trouble starts with clean ports and a seated cap. LP conversion or a wrong gas type needs a technician.
Owner care, within the model instructions.
Turn the appliance off and unplug it before any check you can do yourself. Look out for pooled water and sharp edges. Never touch a wet plug or live area, take off service panels, or go past your model’s owner instructions.
- 1
Read the code exactly
FEE6 is bake, FEE7 is broil. Mention which function you were using when the code appeared.
- 2
Reset the power
Switch the breaker off for one minute, back on, and watch the oven for one minute to see whether the code returns.
- 3
Do not mistake normal cycling for a failure
JennAir says bake and broil elements turn off and on during a cycle by design, through a limiter, and that they stay off while the door is open. A displayed FEE code is a separate message.
- 4
Leave the element alone
The pages do not give a replacement procedure. Never reach into a cavity with the power on.
Cleaning or replacement?
Leave internal testing to a technician.
Book us if the code returns or the oven will not heat in bake or broil.
Book us if you see a blistered, broken or glowing-spotted element.
Book us if the breaker trips when the oven starts.
Arrange a diagnosticSources and model boundaries.
The Bake and broil elements guidance rests on these references. Pick the manual that fits your model.
- FEE6 - Error Code - Range - Product Help | JennAir
- FEE7 - Error Code - Range - Product Help | JennAir
- Oven Elements Turning On/Off - Electric Range - Product Help | JennAir
Go by the instructions for your own model. See how we research these pages.
What do FEE6 and FEE7 mean?
FEE6 points to the main cavity bake element or its wiring, and FEE7 to the broil element or its wiring, per the range pages.
Will the oven work in broil if bake fails?
The pages do not say. Test it once the code is cleared, and book if either function stays cold.
Is a cycling oven element a problem?
JennAir says bake and broil elements cycle on and off normally. A displayed FEE code, or no heat at all, is what points to a failing element.
Do wall ovens print these codes?
In the cached pages FEE6 and FEE7 appear for ranges. Wall ovens use other codes.
Code or symptom, part, service call
Tie the message to what comes next.
JennAir oven temperature problems
JennAir says not to judge oven temperature with a thermometer, because the elements cycle and most thermometers react too slowly. Check preheat time, racks, pan spacing and foil first, then run the biscuit test before any calibration.
Oven repair
Schedule a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, plus the access notes to pass along.

