Error codes explained

JennAir column refrigerator alerts: door, over-temp, filter

A JennAir column refrigerator or freezer gives three alerts you can act on: Door Open after about five minutes with a door ajar, Over-Temp when temperatures stay high, and Replace Filter when the filter is due. Close the door, check the temperature, replace and reset the filter. F3E0-style codes have no steps.

Tall built-in refrigerator door left slightly open in a dark kitchen, light spilling onto the floor.
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work
On this page
Key points
  • Door Open: about five minutes, repeating every two. Shutting the door stops it. 1
  • Over-Temp: fridge above 48°F or freezer above 15°F; press the indicator to silence. 2
  • Replace Filter: icon flashes while dispensing; reset by holding Filter Reset for 3 seconds. 3
  • A flashing interior light can mean a zone key was pressed. 4
  • F3E0 to F3E5, FDE0 and FDEA: no published steps. 56

What do the alerts on a JennAir column refrigerator mean?#

Four of them are everyday messages, not repairs: Door Open, Over-Temp, Replace Filter and a flashing interior light. Each has a plain owner action in JennAir's column pages, and the F#E# codes are a separate case covered at the end. 12345

AlertWhat it tells youWhat to do
Door OpenA door has been left open with cooling onClose it, or press any key to stop the noise 1
Over-TempTemperatures have stayed unusually highPress the Over Temp indicator once the cause is dealt with 2
Replace FilterThe water filter is dueReplace it, then hold Filter Reset for 3 seconds 3
Interior light flashingA cooling zone was selectedPress the zone keys as you intend 4
Close view of a refrigerator interior control strip with five glowing icons above a bowl of blueberries and greens.
Small icons, plain actions. 1234

How long can the door stay open before it alarms?#

JennAir's column page says the Door Open alarm sounds once the refrigerator door or freezer door is left open for 5 minutes while cooling is on. The alarm then repeats every 2 minutes. 1

Close the door to turn off both the alarm and the Door Open alert. To stop the noise with the door still open, press any key. 1

The page also contains a separate line under an "Alarm not working?" heading. It says the door open alarm only flashes after the door has been open for 10 minutes, the audible alarm sounds the first time the door is left open more than 10 minutes, and later door alarms only flash, so you must reset the audible alarm each time. 1 The page prints 5 minutes in one place and 10 in the other and does not say which models follow which. Your owner's manual settles which applies to your model.

Before you decide the alarm is wrong, check what is stopping the door from closing. The page tells you to make sure nothing is preventing it from closing properly. 1

What does the Over-Temp alarm do?#

It warns you when temperatures stay unusually high, to help avoid food spoilage and high energy costs. After the refrigerator is turned on, the alarm and the indicator light activate every 1.5 hours until the refrigerator is below 48°F (9°C) and the freezer below 15°F (-9°C). 2

Press the Over Temp indicator to turn the alarm and the light off. 2 The page also lists the question "Was the refrigerator recently installed?" as one thing to consider. 2

If the temperature does not return to normal, the page sends you to the Temperature Concerns section of the troubleshooting guide. 2 The freezer not freezing page lists those checks.

Do built-in refrigerators behave the same way?#

Close, with small differences. JennAir's page for the built-in refrigerator says its Door Ajar alarm sounds after 2 to 5 minutes with a door or drawer open, depending on the model, then repeats every 2 minutes. 7

On that page, touching any button mutes the alarm while the Door Ajar icon stays lit. 7

Use the page for your own refrigerator style. The column page above applies to JennAir columns only.

Why is the Replace Filter icon flashing?#

Because the water filter is due. JennAir's column page says the Replace Filter icon flashes constantly from the start to the end of dispensing. After 14 days without replacing the filter, it blinks seven times and an alert tone sounds three times at the end of dispensing. 3

JennAir recommends an everydrop water filter for these models. 3 Once the new filter is in, the icon stays lit until you reset the filter status: press and hold the Filter Reset button for 3 seconds, and the Replace Filter indicator turns off when the countdown ends. 3

Hand twisting a white water filter cartridge into its housing at the top inside a stainless refrigerator.
Replace the filter, then hold Filter Reset for 3 seconds. 3

Our water filter entry explains the part, and the water filter guide covers replacement signs.

Why is the interior light flashing?#

Probably because a cooling zone was selected. JennAir's page says select features of the refrigerator or freezer are tied to the perimeter lighting, and that pressing the zone keys lights the matching zones. 4

So a flashing or changing interior light after you touch the keys is the control working, not a problem. 4 If you did not touch anything and the light is flashing, note it for the visit.

What about F3E0, F3E1 and the other F#E# codes?#

JennAir's column pages for these codes print no meaning. The F3E0 page says there is no troubleshooting for the error code, and the FDE0 page says there is currently none. 56 The pages for F3E0 to F3E5, FDE0 and FDEA all say the same.

That means an owner cannot clear them at home, and a reset will not be described by the pages either. Our page on codes without a published meaning lists them. Write down the exact characters and the model number, then book a visit.

  1. 1

    Read the alert#

    Door Open, Over-Temp, Replace Filter, a flashing light or an F#E# code. 12345

  2. 2

    Deal with the cause#

    Close the door, give a new unit time to cool, or replace the filter. 123

  3. 3

    Clear the alert#

    Press any key for the door alarm, the Over Temp indicator for Over-Temp or hold Filter Reset for 3 seconds. 123

  4. 4

    Book a visit for anything left#

    An alarm that returns with a door shut and cold air inside, or any F#E# code, needs a technician. 25

When is a column alert a repair?#

When an alarm keeps coming back after the door has been shut and the cause removed, or when an F#E# code shows. Tell us the exact wording and the model number. 25

The repairs we take on are listed on our refrigerator service page. The Door Alarm entry and the Temperature Alarm entry give the short versions.

Sources#

  1. Door Alarm or Door Open - Column - Product Help | JennAirJennAir Product Help (producthelp.jennair.com) · dateModified 2024-05-01; PH 9981 · PH 9981
  2. Temperature Alarm - Error Code - Column - Product Help | JennAirJennAir Product Help (producthelp.jennair.com) · dateModified 2024-05-01; PH 9985 · PH 9985
  3. Replace Filter Light - Error Code - Column - Product Help | JennAirJennAir Product Help (producthelp.jennair.com) · dateModified 2025-05-19; PH 9984 · PH 9984
  4. Interior Light Flashing - Column - Product Help | JennAirJennAir Product Help (producthelp.jennair.com) · dateModified 2024-05-01; PH 9983 · PH 9983
  5. F3E0 - Error Code - Column - Product Help | JennAirJennAir Product Help (producthelp.jennair.com) · dateModified 2021-04-27; PH 9996 · PH 9996
  6. FDEA - Error Code - Column - Product Help | JennAirJennAir Product Help (producthelp.jennair.com) · dateModified 2021-04-27; PH 9994 · PH 9994
  7. Door Alarm - Error Message - Built-In Refrigerator - Product Help | JennAirJennAir Product Help (producthelp.jennair.com) · dateModified 2021-04-27; PH 9899 · PH 9899

Here to help

Good questions.
Clear answers.

Talk to our team
How long can a column door stay open before the alarm?

JennAir's column page says the Door Open alarm sounds when a refrigerator or freezer door stays open for 5 minutes with cooling on, then repeats every 2 minutes. A separate line on the same page mentions 10 minutes. [1]

How do I silence the Door Open alarm?

Close the door, which turns off both the alarm and the Door Open alert. To stop the noise with the door still open, press any key. [1]

When does the Over-Temp alarm stop?

After the refrigerator is turned on, the alarm and indicator light repeat every 1.5 hours until the refrigerator is below 48°F (9°C) and the freezer below 15°F (-9°C). Press the Over Temp indicator to turn them off. [2]

Why does the Replace Filter icon flash while I pour water?

It flashes during dispensing as a reminder. After 14 days without a new filter it blinks seven times and sounds three tones when dispensing ends. [3]

What do the F#E# codes on a column mean?

JennAir's column pages for F3E0 to F3E5, FDE0 and FDEA print no meaning and no steps. [5][6]

Let’s take care of it.

Something on the display?
Send us the details.