Read the whole display
Say whether the refrigerator is built-in, French-door or a column, and read the indicator or code exactly. The reset differs: one minute for a flashing F, five minutes for Call for Service.
Model-specific code library
We decode 12 refrigerator alerts and indicators across built-in, French-door and column models: PO, the temperature and door alarms, a flashing F, Call for Service, filter lights and the column interior and filter lights.
After replacing the Freshflow air filter on a French-door JennAir refrigerator, you must reset its status: press and hold AIR FILTER for three seconds. The icons switch off, then the air filter icon comes back blue.
Read the Air Filter indicator checks12 researched refrigerator codes. Each model reads codes its own way, so go by your own manual.
After replacing the Freshflow air filter on a French-door JennAir refrigerator, you must reset its status: press and hold AIR FILTER for three seconds. The icons switch off, then the air filter icon comes back blue.
Information onlyA blinking Call for Service light on a built-in JennAir refrigerator calls for a power reset. Breaker off for five minutes, breaker on, then a couple of minutes of observation. If the light returns, schedule service.
Reset, then bookIf the control panel of a built-in JennAir refrigerator will not respond, JennAir asks you to rule out a recent power outage, Showroom or demo mode, and Sabbath mode before resetting the refrigerator. Check those three first.
Owner checks firstCOOLING OFF on a French-door JennAir refrigerator means cooling has been turned off, so neither the refrigerator nor the freezer cools. A common method to turn it back on is pressing LOCK and MEASURED FILL together for three seconds.
Information onlyThe door alarm sounds when a door or freezer drawer has stood open for two to five minutes, the exact time depending on the model, with cooling on. On a column the wait is 5 minutes. Close the door to reset it, or touch any key to mute it while the door stays open.
Owner checks firstA flashing F on a built-in JennAir refrigerator display calls for a power reset: breaker off or unplug for one minute, restore power, make sure cooling is on, and watch for a minute. If the F keeps flashing, schedule service.
Reset, then bookThe H2O light is the water filter reminder on a French-door JennAir refrigerator. Change the filter about twice a year, or when the light comes on, then reset the status by holding LIGHT and ICE TYPE for three seconds.
Information onlyOn a JennAir column refrigerator or freezer, some features are tied to the perimeter lighting. If the interior light flashes, JennAir asks whether a new cooling zone was just selected. Pressing a zone key lights that zone.
Information onlyPO means power to the refrigerator was off long enough for the freezer to reach 18 degrees F (-8 C) or higher. The display reads PO, a tone sounds three times, and Confirm blinks until you press MEASURED FILL under it.
Owner checks firstOn a JennAir column, the Replace Filter icon flashes the whole time water dispenses. After 14 days without a new filter it blinks seven times with three tones at the end of dispensing. Fit a new filter, then hold Filter Reset for three seconds.
Information onlyThe temperature alarm sounds when the refrigerator rises above 48 degrees F (9 C) or the freezer above 15 degrees F (-9 C) for longer than 1.5 hours. The sound stops by itself; the light flashes until you press the alarm key. Column models call it Over-Temp.
Owner checks firstThe water filter status does not reset automatically when you change the filter. On a French-door JennAir the reset depends on the control: Type 1 touches MAX COOL and MAX ICE for three seconds, Type 2 holds FILTER RESET, Type 3 holds WATER FILTER for three seconds.
Owner checks firstF3E0 to F3E5, FDE0 and FDEA on columns are printed with a note that there is no troubleshooting, and rd is not printed. They share one page that says so.

We decode 12 refrigerator alerts and indicators across built-in, French-door and column models: PO, the temperature and door alarms, a flashing F, Call for Service, filter lights and the column interior and filter lights.
F3E0 to F3E5, FDE0 and FDEA on columns are printed with a note that there is no troubleshooting, and rd is not printed. They share one page that says so.
Say whether the refrigerator is built-in, French-door or a column, and read the indicator or code exactly. The reset differs: one minute for a flashing F, five minutes for Call for Service.
If the unit is warming, move food to a cold place. Do not use a refrigerator that sparks or smells of burning; unplug it and book a technician.
On a JennAir the interior lights turn themselves off after the door has been open 10 minutes. Close every door for 1 minute to reset. Then check the door switch, the wiring plug after a delivery, Sabbath mode and the bulb.
JennAir calls a little moisture normal: small ice droplets on the freezer walls and back panel, and sweat on the center mullion or cabinet flanges in humid weather. Check doors, seals, vents and settings before assuming a defrost problem.
Match the leak to its spot. JennAir lists the dispenser tubing at the top, the supply line and valve at the bottom or back, the filter and its O-rings, and drips at the dispenser. JennAir publishes no defrost drain page.
Go by the instructions for your own model. See how we research these pages.
F3E0 to F3E5, FDE0 and FDEA on columns are printed with a note that there is no troubleshooting, and rd is not printed. They share one page that says so.
Take a clear photo of the whole refrigerator display and of the model label. Add what the appliance was doing when the message came up, and do not borrow the explanation for a different appliance.
An old search phrase is no substitute for manufacturer evidence. When our refrigerator documents leave a message undecoded, we show the name only and send you toward help, with no part or cause attached.
Browse the manufacturer documents in this refrigerator library and hold the models on their covers up against your label. Another model needs instructions of its own.