JennAir dishwasher All cycle and option lights flashing / Indicator lights

JennAir dishwasher
error All cycle and option lights flashing

Dishwasher / display referenceAll cycle and option lights flashing

When every cycle and option light flashes together, the cycle has been suspended, most often because the door was opened mid-wash. Push the door shut until it latches; the lights stop and the cycle resumes after a short delay.

Also shown as All cycle and option lights flashing

Last reviewed

Dishwasher / display referenceAll cycle and option lights flashing
Meaning
When every cycle and option light flashes together, the cycle has been suspended, most often because the door was opened mid-wash. Push the door shut until it latches; the lights stop and the cycle resumes after a short delay.
Who handles it
Information only
Source
All Cycle And Option Lights flashing - Dishwasher - Product Help | JennAir

What JennAir dishwasher All cycle and option lights flashing means.

What it means

When every cycle and option light flashes together, the cycle has been suspended, most often because the door was opened mid-wash. Push the door shut until it latches; the lights stop and the cycle resumes after a short delay.

What you can safely check

Push firmly and listen for the latch.

When to call a technician

The lights keep flashing with the door latched.

Checks you have ticked / saved in this browser

Safe checks, in order.

0 of 4 checks done
  1. JennAir dishwasher All cycle and option lights flashing: Lower edge of a closed black dishwasher door in a dim kitchen, three small lit indicator lights and a glow reflected on the floor tile.
    Illustration. Follow your model’s instructions.
    Before you begin

    Shut the door with a firm push

    Push firmly and listen for the latch. The lights stop flashing once the door is properly shut.

  2. Dishwashers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Give it a moment to restart

    After a slight delay, the cycle picks up where it stopped. Do not press Start again straight away, or you may restart from the beginning.

  3. The black glass control strip of a built-in wall oven above its stainless handle
    Illustration. Follow your model’s instructions.
    Check 3

    Check nothing blocks the door

    If the lights keep flashing with the door shut, look for a rack, a handle or a dish edge keeping it from seating.

  4. Over the shoulder view of a person holding a tablet with a blank checklist, a refrigerator behind.
    Illustration. Follow your model’s instructions.
    Check 4

    Power cycle as a last step

    If the flashing carries on, disconnect at the outlet or breaker for half a minute, reconnect, and watch the lights.

Still showing All cycle and option lights flashing?

Send the model and the checks you have already run, then begin your request from this page.

Book a visit

The control and its wiring.

Conceptual dishwasher sectionKeypadControl boardMotor wiringHeater wiring1234
  1. 2Control board
  2. 3Motor wiring
  3. 4Heater wiring

A simplified drawing, because layouts change with the model. Tap an outlined part to see a photo and the related check.

A little more context.

Why do all the lights flash when I open the door?

On models with these lights, the dishwasher signals a suspended cycle by flashing every cycle and option-selected light together. It is the normal response to adding a dish mid-wash, not an error code.

Read the supporting manual

Will opening the door ruin the wash?

JennAir's page says the cycle resumes at the point of interruption after a slight delay once the door closes. A very long pause may cool the water, which matters most on a sanitize cycle.

Read the supporting manual

What if the lights flash even though the door is shut?

Then something may be stopping the latch from engaging, or the control needs a reset. The page closes with a half-minute power cycle.

Read the supporting manual

The manual behind the message.

Manufacturer document

All Cycle And Option Lights flashing - Dishwasher - Product Help | JennAir

JennAir Product Help (producthelp.jennair.com)

dateModified 2026-06-15; PH 12182 / PH 12182 (dishwasher)

Applies to select JennAir dishwasher models with cycle and option lights. Source: product page PH 12182, last modified 2026-06-15.

Here to help

Good questions.
Clear answers.

Talk to our team
Is that the same thing as a single Clean light blinking?

No. A single Clean light flashing signals an error code in a two-part count. All cycle lights flashing together signals a paused cycle.

Does this happen on every JennAir dishwasher?

The page says it applies to select models, so your lights may behave differently.

How long should the delay be after closing?

The page says only a slight delay. If nothing happens after a minute, check the latch and try the reset.

Can I add a dish safely mid-cycle?

The page treats it as normal. Take care with hot water and steam when the door opens.

Does this ever need a technician?

Not unless the flashing continues with the door shut and the reset does not help.

Let’s take care of it.

Something on the display?
Send us the details.