What it means
F1E1 on a JennAir dishwasher names the control module as the potential cause. Start by removing power for half a minute. The Clean light spells the code as a single flash, a gap, and a single flash again.
JennAir dishwasher F1E1 / Controls
F1E1 on a JennAir dishwasher names the control module as the potential cause. Start by removing power for half a minute. The Clean light spells the code as a single flash, a gap, and a single flash again.
Also shown as F1E1
F1E1 on a JennAir dishwasher names the control module as the potential cause. Start by removing power for half a minute. The Clean light spells the code as a single flash, a gap, and a single flash again.
If the dishwasher is hard-wired, switch off the breaker that feeds it.
F1E1 returns after the 30-second power cycle.
Checks you have ticked / saved in this browser

If the dishwasher is hard-wired, switch off the breaker that feeds it. If it plugs into an outlet under the sink, pull the plug. Keep the door shut and leave the panels alone while the power is off.

Count a slow thirty before restoring power. A shorter wait may not let the control clear, and the page gives no shorter interval.

Switch the breaker back on or plug in again, then start a quick cycle with the door closed and see whether the Clean light or display returns to F1E1.

Note whether you saw F1E1 as text or as one flash, a pause and one flash. Include the model number, which sits on the door edge. A technician can start from that.
Send the model and the checks you have already run, then begin your request from this page.
Book a visit
A simplified drawing, because layouts change with the model. Tap an outlined part to see a photo and the related check.
JennAir's page lists the control module as the potential cause of F1E1 and treats a power cycle as the remedy. The page prints nothing more specific, so the code points to the electronics rather than to water, drain or heat.
Read the supporting manualHalf a minute without power, then back on. With a plug, pull it out. When the machine is wired directly, use the breaker. JennAir adds only one more step: if the code comes back, schedule service.
Read the supporting manualF1E1 names the control module. F1E2 and F2E2 each deal with the main control talking to the rest of the machine. The first number in the flash pattern is a different F value in each, so count carefully before you compare.
Read the supporting manualManufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2026-06-15; PH 12191 / PH 12191 (dishwasher)
Manufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2026-06-15; PH 12176 / PH 12176 (dishwasher)
Built-in JennAir dishwashers, both the flashing-light and the text-display versions. Pages used: PH 12191 for the code and PH 12176 for its flash pattern, both modified 2026-06-15.
Yes. JennAir lists the blinking form as one flash, a pause, and one more flash. The page for that pattern gives the same potential cause and the same power cycle.
Do not keep trying. One reset attempt is plenty. If the code still comes back, put the dishwasher aside and book a visit. Repeated starts on a failing control can leave dishes half washed and water in the tub.
JennAir does not say so. The page names the control module and nothing else. A power blip may still cause one-time glitches, which is why one reset is worth trying before any call.
A control board holds its state in memory. Removing power lets that memory clear and start again. It is a first step, not a repair, and it cannot fix a failed component.
They would check the control board and wiring against the model's service data. Bring the exact code, the model number and a note on what the dishwasher was doing at that moment.
Code or symptom, part, service call
JennAir files F1E2 under main control communication errors for its dishwashers. The one remedy printed is a short loss of power, and a technician if the code comes back. On the Clean light, look for one flash, a gap, then two flashes.
JennAir's order is power, then the door and lower rack, then water supply, control lock, delay start, and a one-minute reset. A dishwasher that will not fill adds the drain loop height and an interrupted-cycle flash to the list.
Schedule a diagnostic for your model, carried out at the appliance.
Office details, plus the access notes to pass along.