JennAir dishwasher F1E2 / Controls

JennAir dishwasher
error F1E2

Dishwasher / display reference

JennAir files F1E2 under main control communication errors for its dishwashers. The one remedy printed is a short loss of power, and a technician if the code comes back. On the Clean light, look for one flash, a gap, then two flashes.

Also shown as F1E2

Last reviewed

Dishwasher / display reference
Meaning
JennAir files F1E2 under main control communication errors for its dishwashers. The one remedy printed is a short loss of power, and a technician if the code comes back. On the Clean light, look for one flash, a gap, then two flashes.
Who handles it
Reset, then book
Related codes
Source
F1E2- Dishwasher - Product Help | JennAir

What JennAir dishwasher F1E2 means.

What it means

JennAir files F1E2 under main control communication errors for its dishwashers. The one remedy printed is a short loss of power, and a technician if the code comes back. On the Clean light, look for one flash, a gap, then two flashes.

What you can safely check

Take the plug out of the outlet under the sink.

When to call a technician

F1E2 returns after the power cycle.

Checks you have ticked / saved in this browser

Safe checks, in order.

0 of 4 checks done
  1. JennAir dishwasher F1E2: Open dishwasher door with its top-edge control strip, a row of flat buttons and small lit indicators above loaded racks.
    Illustration. Follow your model’s instructions.
    Before you begin

    Remove power from the dishwasher

    Take the plug out of the outlet under the sink. A wired-in dishwasher needs its own breaker turned off. Leave the door closed. Do not open the electronics area to look at boards.

  2. Dishwashers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Hold for thirty seconds

    Give it a full thirty seconds with no power, then restore it. This is the interval JennAir prints for control resets on its dishwasher pages.

  3. The black glass control strip of a built-in wall oven above its stainless handle
    Illustration. Follow your model’s instructions.
    Check 3

    Run one short cycle

    Start a quick cycle and watch the display or the Clean light. If the code stays away through the first minutes of the cycle, note the date it appeared.

  4. Over the shoulder view of a person holding a tablet with a blank checklist, a refrigerator behind.
    Illustration. Follow your model’s instructions.
    Check 4

    Count the flashes if there is no display

    One quick flash, a one to two second pause, then two flashes. Counting twice keeps you from mixing it up with F2E2, which carries the same wording.

Still showing F1E2?

Send the model and the checks you have already run, then begin your request from this page.

Book a visit

The control and its wiring.

Conceptual dishwasher sectionKeypadControl boardMotor wiringHeater wiring1234
  1. 2Control board
  2. 3Motor wiring
  3. 4Heater wiring

A simplified drawing, because layouts change with the model. Tap an outlined part to see a photo and the related check.

A little more context.

What does a communication error mean on a dishwasher?

The control that runs the cycle and the part that takes your button presses are meant to exchange messages. F1E2 says that exchange failed. JennAir words it as a main control communication error, and the single remedy is a brief loss of power.

Read the supporting manual

What should I do before I book a visit?

Reset once as the page describes, run a short cycle, and write down whether F1E2 returns. If it does, the page says to schedule service. Having the model number ready shortens the visit.

Read the supporting manual

Is F1E2 the same as F2E2?

No. JennAir uses the same words for both, yet the first number of the code differs, so the pages are separate. If your light shows one flash then two, treat it as F1E2.

Read the supporting manual

The manual behind the message.

Manufacturer document

F1E2- Dishwasher - Product Help | JennAir

JennAir Product Help (producthelp.jennair.com)

dateModified 2026-06-15; PH 14218 / PH 14218 (dishwasher)

JennAir dishwasher pages, source PH 14218, last modified 2026-06-15.

Here to help

Good questions.
Clear answers.

Talk to our team
Does F1E2 mean the dishwasher is leaking?

No. The page ties it to communication in the control, not to water. Should puddles appear near the machine, switch the power off and treat that as its own problem.

Will the reset erase my cycle settings?

JennAir does not mention it. On most dishwashers a short power loss only returns the control to idle. Choose your cycle again after restoring power.

The dishwasher still washes with F1E2 showing. Can I use it?

The page does not say. We would stop after one reset attempt: a control that cannot talk to its own panel may behave unpredictably during a cycle.

Is F1E2 an installation problem on a new JennAir?

Installation is not mentioned as a cause. Installers should not need to touch the control. If it appears on day one, mention the install date when you book.

How long does the 30 seconds really need to be?

JennAir prints thirty seconds for the unplug or breaker step. Longer is harmless, shorter is not what the page says. Use a clock instead of guessing.

Let’s take care of it.

Something on the display?
Send us the details.