What it means
JennAir reads 1d21 as trouble with the temperature sensor and/or the control or the wiring. Cut the circuit breaker for sixty seconds, bring back power, and monitor the code.
JennAir oven 1d21 / Temperature sensor
JennAir reads 1d21 as trouble with the temperature sensor and/or the control or the wiring. Cut the circuit breaker for sixty seconds, bring back power, and monitor the code.
Also shown as 1d21
JennAir reads 1d21 as trouble with the temperature sensor and/or the control or the wiring. Cut the circuit breaker for sixty seconds, bring back power, and monitor the code.
Give racks and door glass to cool with 1d21 showing.
1d21 returns after the breaker reset.
Checks you have ticked / saved in this browser

Give racks and door glass to cool with 1d21 showing.

Breaker off for a solid minute, and back on; watch for 1d21 for another minute.

Copy 1d21 as displayed, and what the oven was doing at that moment.

The sensing probe is a thin rod inside the cavity; keep foil and pans off it when 1d21 appears.
Send the model and the checks you have already run, then begin your request from this page.
Book a visitA simplified drawing, because layouts change with the model. Tap an outlined part to see a photo and the related check.

Component reference
JennAir Product Help ties F1, F2 and several F3 codes to the oven temperature sensor, the control or the wiring between them.
Read the definition
Component reference
The electronic control is the board that manages the oven functions.
Read the definitionFor 1d21 JennAir stays careful: the sensing probe and/or the electronic control may be involved. A lead, not a verdict.
Read the supporting manualThe page's fix for 1d21 is a breaker reset for one minute. Then a minute of watching.
Read the supporting manualThis is our advice, not the page's: cook only while it behaves. Smoke, sparks or tripping mean power off plus a technician.
Read the supporting manualJennAir prints the same suspects for 1d22: the sensing probe and/or the control. Numbers alone do not separate 1d21 from it.
Read the supporting manualManufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2024-08-16; PH 12899 / PH 12899 (range)
Manufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2024-11-08; PH 13273 / PH 13273 (wall oven)
Appliances covered: freestanding range and wall oven. Basis: JennAir Product Help PH 12899, PH 13273. One printed line for 1d21, so our guidance is general.
Product Help lists the sensing probe or the control board or its wiring as suspects for 1d21.
Breaker off for a minute, then on, then observe 1d21 for 60 seconds.
Not while 1d21 shows. Reset first, then cook if it heats normally.
No, not by itself. JennAir gives 1d21 suspects, not a diagnosis.
Code or symptom, part, service call
On a JennAir oven, 1d22 points to the temperature sensor or the control or the wiring. Open with a one-minute breaker cycle, then watch for the code for a minute.
JennAir says not to judge oven temperature with a thermometer, because the elements cycle and most thermometers react too slowly. Check preheat time, racks, pan spacing and foil first, then run the biscuit test before any calibration.
JennAir Product Help ties F1, F2 and several F3 codes to the oven temperature sensor, the control or the wiring between them. The sensor reports cavity heat to the control. The help pages pair it with the control, so one reset is the only owner step.
Schedule a diagnostic for your model, carried out at the appliance.
Office details, plus the access notes to pass along.