What it means
On a JennAir oven, 1d22 points to the temperature sensor or the control or the wiring. Open with a one-minute breaker cycle, then watch for the code for a minute.
JennAir oven 1d22 / Temperature sensor
On a JennAir oven, 1d22 points to the temperature sensor or the control or the wiring. Open with a one-minute breaker cycle, then watch for the code for a minute.
Also shown as 1d22
On a JennAir oven, 1d22 points to the temperature sensor or the control or the wiring. Open with a one-minute breaker cycle, then watch for the code for a minute.
Leave panels on while 1d22 shows; the wiring is live.
1d22 returns after the breaker reset.
Checks you have ticked / saved in this browser

Leave panels on while 1d22 shows; the wiring is live.

Use the breaker panel, not the oven; after a minute, check for 1d22 again.

Time, setting and cycle when 1d22 first appeared help the visit.

An oven thermometer on the middle rack gives you a second reading while 1d22 is in doubt.
Send the model and the checks you have already run, then begin your request from this page.
Book a visitA simplified drawing, because layouts change with the model. Tap an outlined part to see a photo and the related check.

Component reference
JennAir Product Help ties F1, F2 and several F3 codes to the oven temperature sensor, the control or the wiring between them.
Read the definition
Component reference
The electronic control is the board that manages the oven functions.
Read the definitionOn 1d22 JennAir is cautious: the temperature sensor or the main control may be to blame. Not a diagnosis.
Read the supporting manualJennAir's fix for 1d22 is a breaker reset for 60 seconds. Then watch for a minute.
Read the supporting manualWhen it runs normally after the reset, careful use is reasonable. A second 1d22 means stop and schedule a visit.
Read the supporting manualJennAir gives the same suspects for 3d11: the temperature sensor or the electronic control. Numbers alone do not separate 1d22 from it.
Read the supporting manualManufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2024-08-16; PH 12900 / PH 12900 (range)
Manufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2024-11-08; PH 13274 / PH 13274 (wall oven)
Appliances covered: freestanding range and wall oven. Cited: JennAir Product Help PH 12900, PH 13274. One printed line for 1d22, so our guidance is general.
Product Help lists the temperature sensor and/or the oven control or its wiring as suspects for 1d22.
Breaker off for a minute, then restore power, then observe 1d22 a minute.
Not while 1d22 shows. Reset, then judge, then short bakes are fine.
No, not by itself. JennAir lists suspects for 1d22, not a verdict.
Code or symptom, part, service call
3d11 opens the "Starts with 3d" group and lists the temperature sensor and the control, or the wiring between them. The first step is a sixty-second power reset at the breaker panel; call for service if it returns.
JennAir says not to judge oven temperature with a thermometer, because the elements cycle and most thermometers react too slowly. Check preheat time, racks, pan spacing and foil first, then run the biscuit test before any calibration.
JennAir Product Help ties F1, F2 and several F3 codes to the oven temperature sensor, the control or the wiring between them. The sensor reports cavity heat to the control. The help pages pair it with the control, so one reset is the only owner step.
Schedule a diagnostic for your model, carried out at the appliance.
Office details, plus the access notes to pass along.