What it means
F3 E9 names the lower oven temperature sensor on a wall oven, and on a professional-style range it is a meat probe seating check with a reset. Seat the probe using a mitt, cancel the error, then power cycle.
JennAir oven F3E9 / Temperature sensor
F3 E9 names the lower oven temperature sensor on a wall oven, and on a professional-style range it is a meat probe seating check with a reset. Seat the probe using a mitt, cancel the error, then power cycle.
Also shown as F3E9
F3 E9 names the lower oven temperature sensor on a wall oven, and on a professional-style range it is a meat probe seating check with a reset. Seat the probe using a mitt, cancel the error, then power cycle.
Professional-style ranges: make sure the meat probe is fully plugged in, with the oven cool or protected.
F3 E9 returns after the probe is seated and power is cycled.
Checks you have ticked / saved in this browser

Professional-style ranges: make sure the meat probe is fully plugged in, with the oven cool or protected.

The 2024 pro page says this cancels the error.

Five minutes without power on the 2025 pro page; one minute at the breaker on a wall oven.

Wall oven means the lower cavity. Pro-range means the probe route.
Send the model and the checks you have already run, then begin your request from this page.
Book a visit
A simplified drawing, because layouts change with the model. Tap an outlined part to see a photo and the related check.

Component reference
JennAir Product Help ties F1, F2 and several F3 codes to the oven temperature sensor, the control or the wiring between them.
Read the definitionJennAir says the temperature sensor, the oven control or the cabling is the suspected trouble spot. The same line appears for E5 to E8.
Read the supporting manualThe 2025 page asks you to ensure the meat probe is fully seated and then power cycle for five minutes. The 2024 page gives only the knob-to-OFF reset.
Read the supporting manualJennAir does not explain why the pro-range row differs from the wall oven row, so we do not guess.
Read the supporting manualCycle the power and run a short bake. If E9 returns without the probe in use, the sensor or control needs testing.
Read the supporting manualManufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2025-10-01; PH 14148 / PH 14148 (professional-style range)
Manufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2024-11-05; PH 13095 / PH 13095 (professional-style range)
Manufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2024-11-08; PH 13343 / PH 13343 (wall oven)
PH 14148, 13095, 13343: F3E9, pro-range/wall-oven.
The pro-range pages read alike for both: seat the probe, then reset. The wall oven rows differ.
Yes, if the oven heats normally. Leave the probe out until it has been checked.
JennAir does not say why. The newer edition simply asks for a longer power disconnection.
A diagnostic visit finds the cause. We do not quote prices from a code alone.
Code or symptom, part, service call
F3 on a JennAir freestanding range or wall oven points at the oven control or its wiring, and on a steam wall oven the page only asks for a breaker reset. Switch the oven breaker off for a single minute, switch it back on, then watch the display for another minute.
JennAir says not to judge oven temperature with a thermometer, because the elements cycle and most thermometers react too slowly. Check preheat time, racks, pan spacing and foil first, then run the biscuit test before any calibration.
JennAir Product Help ties F1, F2 and several F3 codes to the oven temperature sensor, the control or the wiring between them. The sensor reports cavity heat to the control. The help pages pair it with the control, so one reset is the only owner step.
Schedule a diagnostic for your model, carried out at the appliance.
Office details, plus the access notes to pass along.