What it means
F6 E1 on a professional-style range means the oven got too hot during self-clean and the controls lock until it cools. On a range or wall oven JennAir names the appliance manager, with the converter control on wall ovens.
JennAir oven F6E1 / Appliance manager
F6 E1 on a professional-style range means the oven got too hot during self-clean and the controls lock until it cools. On a range or wall oven JennAir names the appliance manager, with the converter control on wall ovens.
Also shown as F6E1
F6 E1 on a professional-style range means the oven got too hot during self-clean and the controls lock until it cools. On a range or wall oven JennAir names the appliance manager, with the converter control on wall ovens.
If a clean cycle ran, the cavity may be extremely hot.
F6 E1 returns after cool-down and reset.
Checks you have ticked / saved in this browser

If a clean cycle ran, the cavity may be extremely hot. Wait until it is fully cool.

The pro-range controls stay locked until it does.

Five minutes on the 2025 pro page; knob to OFF on the 2024 one; a minute at the breaker for others.

Do not start another cycle until the code has stayed away.
Send the model and the checks you have already run, then begin your request from this page.
Book a visit

A simplified drawing, because layouts change with the model. Tap an outlined part to see a photo and the related check.

Component reference
JennAir ranges and wall ovens with several cavities use an appliance manager that coordinates the oven controls.
Read the definitionThe 2025 page asks whether you were running a self-clean. It says the error means the oven got too hot during the cycle, and the controls lock to protect the range.
Read the supporting manualThe appliance manager on a range; the appliance manager control or the converter control on a wall oven; plus wiring.
Read the supporting manualA converter control changes supply to the voltages the electronics use. It is a board, not a user part.
Read the supporting manualNo. Wait for cool-down.
Read the supporting manualManufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2025-10-01; PH 14154 / PH 14154 (professional-style range)
Manufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2024-11-05; PH 13101 / PH 13101 (professional-style range)
Manufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2024-08-16; PH 12982 / PH 12982 (range)
Manufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2024-11-18; PH 13368 / PH 13368 (wall oven)
PH 14154, 13101, 12982, 13368: F6E1, pro-range/range/wall-oven.
Until the oven cools. JennAir gives no minutes.
The page does not say so.
The pro page for E3 repeats the same self-clean wording.
Only after a stable week of normal use.
Code or symptom, part, service call
F6 E2 appears only in the wall oven tables: JennAir names the appliance manager control, the converter control or the wiring. Cycle the breaker for a single minute, restore power, and watch the display for another minute.
JennAir says not to judge oven temperature with a thermometer, because the elements cycle and most thermometers react too slowly. Check preheat time, racks, pan spacing and foil first, then run the biscuit test before any calibration.
JennAir ranges and wall ovens with several cavities use an appliance manager that coordinates the oven controls. The F6 family names it, sometimes with the converter control or the user interface. The pages admit there are many possible reasons, then give one reset.
Schedule a diagnostic for your model, carried out at the appliance.
Office details, plus the access notes to pass along.