What it means
F6 E3 repeats the self-clean overheating message on a professional-style range and lists the appliance manager on a range, with the converter control on a wall oven. Let the oven cool, then restart power.
JennAir oven F6E3 / Appliance manager
F6 E3 repeats the self-clean overheating message on a professional-style range and lists the appliance manager on a range, with the converter control on a wall oven. Let the oven cool, then restart power.
Also shown as F6E3
F6 E3 repeats the self-clean overheating message on a professional-style range and lists the appliance manager on a range, with the converter control on a wall oven. Let the oven cool, then restart power.
If a clean cycle was running, the cavity may be extremely hot.
F6 E3 returns after cooling and a reset.
Checks you have ticked / saved in this browser

If a clean cycle was running, the cavity may be extremely hot.

The pro page says the controls stay locked until it does.

Five minutes disconnected on the 2025 page, knob to OFF on the 2024 one, a minute at the breaker otherwise.

Run normal bakes first and see whether the code returns.
Send the model and the checks you have already run, then begin your request from this page.
Book a visit

A simplified drawing, because layouts change with the model. Tap an outlined part to see a photo and the related check.

Component reference
JennAir ranges and wall ovens with several cavities use an appliance manager that coordinates the oven controls.
Read the definitionIt asks whether a self-clean was running and says the interior got too hot, so the controls lock to protect the range.
Read the supporting manualThe range page names the appliance manager. The wall oven page adds the converter control. Both mention wiring.
Read the supporting manualThe pro-range pages for E1 and E3 use the same self-clean wording. JennAir does not say what the digits separate.
Read the supporting manualThen the self-clean reading does not fit, so the appliance manager or wiring on your product type is the page's suggestion.
Read the supporting manualManufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2025-10-01; PH 14155 / PH 14155 (professional-style range)
Manufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2024-11-05; PH 13102 / PH 13102 (professional-style range)
Manufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2024-08-16; PH 12983 / PH 12983 (range)
Manufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2024-11-18; PH 13370 / PH 13370 (wall oven)
PH 14155, 13102, 12983, 13370: F6E3, pro-range/range/wall-oven.
No. JennAir says the controls stay locked until the oven cools.
Leave the door closed and let it be. Do not spray water into a hot cavity.
The page does not blame the user.
Wait until normal use has been clean for a while.
Code or symptom, part, service call
F6 E4 asks for a reset on a professional-style range, names the oven appliance manager or oven control on a freestanding range, and the appliance manager control on a wall oven. Restart power for the time your page gives.
JennAir says not to judge oven temperature with a thermometer, because the elements cycle and most thermometers react too slowly. Check preheat time, racks, pan spacing and foil first, then run the biscuit test before any calibration.
JennAir ranges and wall ovens with several cavities use an appliance manager that coordinates the oven controls. The F6 family names it, sometimes with the converter control or the user interface. The pages admit there are many possible reasons, then give one reset.
Schedule a diagnostic for your model, carried out at the appliance.
Office details, plus the access notes to pass along.