Start from the symptom
JennAir dishwasher leaking.
Find where the water shows. At the door edge, think gasket, suds, blocked seal or level. Underneath or behind, think connections and hoses. If the float switch trips, F8E4 means water was detected in the drip tray.

Start with safe observations.
Turn the appliance off and unplug it before any check you can do yourself. Look out for pooled water and sharp edges. Never touch a wet plug or live area, take off service panels, or go past your model’s owner instructions.
- 1
Stop the leak first
Switch off power at the breaker and close the water valve. Mop up and avoid running it until the source is found.
- 2
Door and front
Look for a cracked or dirty door seal, and utensils or dishes stuck at the door. Level the dishwasher with a level in both directions.
- 3
Suds
Dish soap or too much detergent makes foam that can push water out. Use dishwasher detergent only.
- 4
Underneath or behind
Check water supply and drain connections for tightness and damage.
- 5
F8E4
This code means water in the drip tray. Check the fittings, the float switch connection and empty the tray.
Systems a technician may investigate.
The symptom connects to these parts. What you observed cannot show that any single one has failed.
If the display adds a code.
Water
JennAir's reading page words F8E4 as Water Detected in Drip Tray. Turn off the water supply, press Cancel once to silence the tone, leave the door shut and do not turn the power off. The dishwasher drains and blocks operation. Then book a visit.
Water
F6E3 means excessive suds on JennAir's dishwasher page. Scoop out the foam, remove the dishes, add 2 to 3 tablespoons of vegetable oil, then run a full cycle with no detergent, followed by a cycle with the dispensers filled but no dishes.
Read the related care guide.

New dishwasher full of water? Check the install.
A newly installed JennAir dishwasher that will not drain usually has a setup problem: the disposer knockout plug is still in, the hose is kinked, or the drain loop or air gap is missing. Check those before you suspect the pump. Power the dishwasher off before you touch the hose. [1][2]

Drips under the counter? Steam or a leak.
Moisture on the underside of the counter near a JennAir dishwasher is usually condensation: steam from the vent meeting a cooler surface. A leak looks different, with water at the door edge, on the floor or under the unit. Check where the water shows up, and when. [1][2]
When observation becomes a service request.
Leave internal testing to a technician.
Water appears from under the unit, F8E4 returns, or you cannot trace the source. Turn off the water and power, then book a visit.
Arrange a diagnosticSources and model boundaries.
The JennAir dishwasher leaking guidance rests on these references. Pick the manual that fits your model.
- Dishwasher Leaking Troubleshooting Guide - Product Help | JennAir
- Leaking - Product Help | JennAir
- F8E4 - Error Code - Dishwasher - Product Help | JennAir
- Removing Suds, Bubbles or Soap Foam from Dishwasher - Product Help | JennAir
Go by the instructions for your own model. See how we research these pages.
What makes water seep out under my JennAir dishwasher door?
JennAir names a worn or dirty door seal, items blocking the door, suds and an unlevel unit among the causes.
Can dish soap cause a leak?
Yes. JennAir says hand-wash soap foams excessively, and foam can lead to leaks. Use dishwasher detergent only.
What does F8E4 mean?
JennAir lists it as water detected in the drip tray. Empty the tray, check the float switch, and look at the water connections.
What should I do first when it leaks?
Cut power at the breaker and close the water valve before cleanup.
Code or symptom, part, service call
Tie the message to what comes next.
JennAir dishwasher F8E4 error code
JennAir's reading page words F8E4 as Water Detected in Drip Tray. Turn off the water supply, press Cancel once to silence the tone, leave the door shut and do not turn the power off. The dishwasher drains and blocks operation. Then book a visit.
JennAir dishwasher won't start or fill
JennAir's order is power, then the door and lower rack, then water supply, control lock, delay start, and a one-minute reset. A dishwasher that will not fill adds the drain loop height and an interrupted-cycle flash to the list.
Float switch and drip tray
The float switch watches for too much water. JennAir F6E4 is "Water Float Switch", and the page asks if the dishwasher is level. F8E4 is "Water Detected in Drip Tray": check the supply connection, the float connector and empty the tray.
Dishwasher repair
Schedule a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, plus the access notes to pass along.
