Start from the symptom
JennAir dishwasher not draining.
For standing water, JennAir's order is filter, drain hose and kinks, the disposer and its knockout plug on a new install, an air gap if fitted, then a power reset. F9E1 is its long-drain code.

Start with safe observations.
Turn the appliance off and unplug it before any check you can do yourself. Look out for pooled water and sharp edges. Never touch a wet plug or live area, take off service panels, or go past your model’s owner instructions.
- 1
Turn off power and water
Use the breaker, not only the panel, before opening the filter or hoses.
- 2
Clean the filter
Remove it and rinse it thoroughly under running water.
- 3
Check the hose
Look for kinks, pinches or a clog between the dishwasher and the sink.
- 4
Check the disposer
On a new install, the knockout plug must be removed. Run the disposer to clear food, then start a drain.
- 5
Check the loop height
The hose should loop high or use an air gap so water cannot flow back. JennAir also asks for the loop at least 20 inches above the floor.
- 6
Reset
Cycle power. If F9E1 returns, the drain issue is still there.
Systems a technician may investigate.
The symptom connects to these parts. What you observed cannot show that any single one has failed.
Read the related care guide.

New dishwasher full of water? Check the install.
A newly installed JennAir dishwasher that will not drain usually has a setup problem: the disposer knockout plug is still in, the hose is kinked, or the drain loop or air gap is missing. Check those before you suspect the pump. Power the dishwasher off before you touch the hose. [1][2]

Drips under the counter? Steam or a leak.
Moisture on the underside of the counter near a JennAir dishwasher is usually condensation: steam from the vent meeting a cooler surface. A leak looks different, with water at the door edge, on the floor or under the unit. Check where the water shows up, and when. [1][2]
When observation becomes a service request.
Leave internal testing to a technician.
Water remains after the filter, hose and disposer checks, the pump hums without moving water, or F9E1 keeps returning. Schedule a technician visit.
Arrange a diagnosticSources and model boundaries.
The JennAir dishwasher not draining guidance rests on these references. Pick the manual that fits your model.
- Dishwasher Not Draining - Product Help | JennAir
- Newly Installed Dishwasher Not Draining - Product Help | JennAir
- Checking the Drain Loop Height - Product Help | JennAir
- Odor From Garbage Disposal - Dishwasher - Product Help | JennAir
- F9E1 - Dishwasher - Product Help | JennAir
Go by the instructions for your own model. See how we research these pages.
Why is my new JennAir dishwasher not draining?
JennAir says a common miss is the garbage disposer knockout plug left in place. Also check for a kinked hose and the drain loop.
What does F9E1 mean on a JennAir?
JennAir lists it as a long drain. Check the filter, hose, disposer and air gap, then cycle power.
Does the drain loop matter?
Yes. A proper high loop or air gap prevents backflow, and JennAir wants it at least 20 inches above the floor.
Why does the dishwasher smell like the disposer?
JennAir says to run the disposer to clear debris and clean both appliances with affresh.
Code or symptom, part, service call
Tie the message to what comes next.
JennAir dishwasher F9E1 error code
F9E1 on a JennAir dishwasher is listed as Long Drain, meaning the water is not leaving the tub. The page's checks run from the filter to the drain hose, the sink disposer knockout plug on a new installation, the air gap and suds. Cycle the power after the checks.
JennAir dishwasher won't start or fill
JennAir's order is power, then the door and lower rack, then water supply, control lock, delay start, and a one-minute reset. A dishwasher that will not fill adds the drain loop height and an interrupted-cycle flash to the list.
Dishwasher removable filter
JennAir dishwashers with a removable filter ask you to clean it by hand under running water, with a soft brush for hard-water deposits. Abrasive pads and wire brushes are out, and the dishwasher should not operate without both filters in place.
Dishwasher repair
Schedule a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, plus the access notes to pass along.
