JennAir dishwasher Sanitize light flashing / Indicator lights

JennAir dishwasher
error Sanitize light flashing

Dishwasher / display referenceSanitize light flashing

A flashing Sanitize light means the dishwasher did not reach the temperature needed for sanitizing, so the dishes were not sanitized. Check that the hot water at the dishwasher reaches at least 120 degrees F (49 C), and avoid opening the door mid-cycle.

Also shown as Sanitize light flashing

Last reviewed

Dishwasher / display referenceSanitize light flashing
Meaning
A flashing Sanitize light means the dishwasher did not reach the temperature needed for sanitizing, so the dishes were not sanitized. Check that the hot water at the dishwasher reaches at least 120 degrees F (49 C), and avoid opening the door mid-cycle.
Who handles it
Owner checks first, then a technician
Source
Sanitize Light Flashing - Dishwasher - Product Help | JennAir

What JennAir dishwasher Sanitize light flashing means.

What it means

A flashing Sanitize light means the dishwasher did not reach the temperature needed for sanitizing, so the dishes were not sanitized. Check that the hot water at the dishwasher reaches at least 120 degrees F (49 C), and avoid opening the door mid-cycle.

What you can safely check

At the sink nearest the dishwasher, run the hot water for roughly half a minute.

When to call a technician

The light flashes again with hot water at the right temperature.

Checks you have ticked / saved in this browser

Safe checks, in order.

0 of 4 checks done
  1. JennAir dishwasher Sanitize light flashing: Lower edge of a closed black dishwasher door in a dim kitchen, three small lit indicator lights and a glow reflected on the floor tile.
    Illustration. Follow your model’s instructions.
    Before you begin

    Run the hot tap for about thirty seconds

    At the sink nearest the dishwasher, run the hot water for roughly half a minute. This clears cold water from the pipe.

  2. Dishwashers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Check the water temperature

    The water should reach at least 120 degrees F (49 C), the minimum JennAir cites from the owner's manual. A kitchen thermometer held in the stream gives a reading.

  3. The black glass control strip of a built-in wall oven above its stainless handle
    Illustration. Follow your model’s instructions.
    Check 3

    Keep the door shut during the cycle

    Opening the door lets heat escape, and the sanitize temperature may then not be met.

  4. Over the shoulder view of a person holding a tablet with a blank checklist, a refrigerator behind.
    Illustration. Follow your model’s instructions.
    Check 4

    Power cycle if the light still flashes

    Take off power for thirty seconds, restore it, and run the cycle again.

Still showing Sanitize light flashing?

Send the model and the checks you have already run, then begin your request from this page.

Book a visit

The control and its wiring.

Conceptual dishwasher sectionKeypadControl boardMotor wiringHeater wiring1234
  1. 2Control board
  2. 3Motor wiring
  3. 4Heater wiring

A simplified drawing, because layouts change with the model. Tap an outlined part to see a photo and the related check.

A little more context.

Why is the Sanitize light flashing?

The dishwasher detected that the temperature needed for sanitizing was not met. JennAir calls it a clear sign the dishes were not sanitized, so treat that load as washed only.

Read the supporting manual

Is my water heater the problem?

It can be. The page tells you to check the water at the dishwasher against 120 degrees F (49 C), which points to the supply first. If supply is hot enough and the light repeats, book a visit.

Read the supporting manual

Does opening the door matter?

Yes. The page says heat can escape if the door was opened mid-cycle, so the right temperature may not have been reached. It also lists a power interruption as something to ask about.

Read the supporting manual

The manual behind the message.

Manufacturer document

Sanitize Light Flashing - Dishwasher - Product Help | JennAir

JennAir Product Help (producthelp.jennair.com)

dateModified 2025-05-27; PH 12184 / PH 12184 (dishwasher)

Manufacturer document

Sanitize Light Flashing - Dishwasher - Product Help | JennAir

JennAir Product Help (producthelp.jennair.com)

dateModified 2025-05-27; PH 12208 / PH 12208 (dishwasher)

Covers the Sanitize light on JennAir dishwashers. Sources: PH 12184 and PH 12208, both last modified 2025-05-27.

Here to help

Good questions.
Clear answers.

Talk to our team
Should I rewash the dishes?

Yes, if sanitizing matters. Run the sanitize cycle again with proper hot water.

What temperature should my water heater be set to?

The page gives the dishwasher minimum of 120 degrees F at the dishwasher, not a water heater setting.

Does it flash during normal cycles?

It is specific to sanitizing. A normal cycle does not need that temperature.

Can power loss cause the light to flash?

The page asks whether power was interrupted, so it can.

When is a technician the next step?

When the water is hot enough, the door stayed shut and the light keeps flashing.

Let’s take care of it.

Something on the display?
Send us the details.