JennAir oven Feature Not Available or Fault Detected / Control message

JennAir oven
error Feature Not Available or Fault Detected

Oven / display referenceFeature Not Available or Fault Detected

Feature Not Available or Fault Detected scrolls across a JennAir range or wall oven display when the control found an error while you were setting a cook cycle. Follow the text on screen, then reset power at the breaker for 60 seconds.

Also shown as Feature Not Available or Fault Detected

Last reviewed

Oven / display referenceFeature Not Available or Fault Detected
Meaning
Feature Not Available or Fault Detected scrolls across a JennAir range or wall oven display when the control found an error while you were setting a cook cycle. Follow the text on screen, then reset power at the breaker for 60 seconds.
Who handles it
Reset, then book
Source
Feature Not Available or Fault Detected - Range - Product Help | JennAir

What JennAir oven Feature Not Available or Fault Detected means.

What it means

Feature Not Available or Fault Detected scrolls across a JennAir range or wall oven display when the control found an error while you were setting a cook cycle. Follow the text on screen, then reset power at the breaker for 60 seconds.

What you can safely check

It says to press Enter to try again or disable power to clear it.

When to call a technician

The message returns after the reset on the same feature.

Checks you have ticked / saved in this browser

Safe checks, in order.

0 of 4 checks done
  1. JennAir oven Feature Not Available or Fault Detected: Wall oven with its door open and a lit message on the display above, the meat probe receptacle visible on the cavity side wall.
    Illustration. Follow your model’s instructions.
    Before you begin

    Read the scrolling text

    It says to press Enter to try again or disable power to clear it.

  2. Ranges & ovens in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Try the setting again once

    Press Enter as the display asks.

  3. The black glass control strip of a built-in wall oven above its stainless handle
    Illustration. Follow your model’s instructions.
    Check 3

    If it repeats, cut the breaker for about a minute

    Then restore it and watch.

  4. Over the shoulder view of a person holding a tablet with a blank checklist, a refrigerator behind.
    Illustration. Follow your model’s instructions.
    Check 4

    Note which feature you chose

    Convection, probe, delay start or timer; the technician will ask.

Still showing Feature Not Available or Fault Detected?

Send the model and the checks you have already run, then begin your request from this page.

Book a visit

The touch panel and control.

Conceptual Range / oven sectionKeypad / touch panelControl boardElement wiring123
  1. 3Element wiring

A simplified drawing, because layouts change with the model. Tap an outlined part to see a photo and the related check.

A little more context.

What triggers this message?

The control detected an error while you were programming a cook cycle. The message is generic and does not name a part.

Read the supporting manual

What does JennAir tell me to do?

Follow the instructions on the display, and if it persists reset power at the breaker for a single minute.

Read the supporting manual

Is it the same on a range and a wall oven?

Yes. Both pages share the wording, with no product-specific part list.

Read the supporting manual

When is a visit needed?

When the message returns on the same feature, which suggests a control or sensor problem tied to it.

Read the supporting manual

The manual behind the message.

Manufacturer document

Feature Not Available or Fault Detected - Range - Product Help | JennAir

JennAir Product Help (producthelp.jennair.com)

dateModified 2024-11-07; PH 13124 / PH 13124 (range)

Manufacturer document

Feature Not Available or Fault Detected - Wall Oven - Product Help | JennAir

JennAir Product Help (producthelp.jennair.com)

dateModified 2024-11-08; PH 13253 / PH 13253 (wall oven)

PH 13124, 13253: FEATURE-NOT-AVAILABLE, range/wall-oven.

Here to help

Good questions.
Clear answers.

Talk to our team
Does it mean the feature is gone?

Not permanently. It means the control could not set it just now.

Is it the same as an F-code?

No. It is a scrolling message with no number.

Can I use other cook modes?

Try a simple bake.

Why is Fault Detected in the title?

That is how JennAir prints the message name. We keep it exactly as printed.

Let’s take care of it.

Something on the display?
Send us the details.