JennAir microwave E24 / Sensors

JennAir microwave
error E24

Microwave / display reference

With E24 the cavity registered an overheat reading of 500 F (260 C). JennAir lists the thermal sensor, the gas sensor, the board or the wiring. Turn the microwave breaker off for a minute and on again.

Also shown as E24

Last reviewed

Microwave / display reference
Meaning
With E24 the cavity registered an overheat reading of 500 F (260 C). JennAir lists the thermal sensor, the gas sensor, the board or the wiring. Turn the microwave breaker off for a minute and on again.
Who handles it
Reset, then book
Related codes
Source
E24 - Error Code - Over-the-Range Microwave - Product Help | JennAir

What JennAir microwave E24 means.

What it means

With E24 the cavity registered an overheat reading of 500 F (260 C). JennAir lists the thermal sensor, the gas sensor, the board or the wiring. Turn the microwave breaker off for a minute and on again.

What you can safely check

An overheat reading means the cavity has been hot.

When to call a technician

E24 returns after cooling and a reset.

Checks you have ticked / saved in this browser

Safe checks, in order.

0 of 4 checks done
  1. JennAir microwave E24: Hand wiping the ceiling of a stainless built-in microwave cavity with a gray cloth, a small perforated vent opening visible on the side wall.
    Illustration. Follow your model’s instructions.
    Before you begin

    Stop cooking and let it cool

    An overheat reading means the cavity has been hot. Open the door carefully, since the cavity and contents may be hot.

  2. The black glass control strip of a built-in wall oven above its stainless handle
    Illustration. Follow your model’s instructions.
    Check 2

    Turn the breaker off for a minute

    Switch it back on afterward.

  3. Over the shoulder view of a person holding a tablet with a blank checklist, a refrigerator behind.
    Illustration. Follow your model’s instructions.
    Check 3

    Watch the display

    See whether E24 returns within the first minute.

  4. A technician reading a built-in oven display
    Illustration. Follow your model’s instructions.
    Check 4

    Verify operation

    Run a short test only after the cooling.

Still showing E24?

Send the model and the checks you have already run, then begin your request from this page.

Book a visit

Microwave control.

Conceptual Microwave sectionKeypadControl boardHumidity sensorWiring1234
  1. 4Wiring

A simplified drawing, because layouts change with the model. Tap an outlined part to see a photo and the related check.

A little more context.

What does E24 mean on a JennAir over-the-range microwave?

The cavity registered an overheat reading of 500 F (260 C).

Read the supporting manual

What should I do first?

Let the cavity cool, then turn the microwave breaker off for a minute, switch it on and watch the display.

Read the supporting manual

When should a technician look?

If E24 returns after cooling. A repeating overheat reading should not be ignored.

Read the supporting manual

The manual behind the message.

Manufacturer document

E24 - Error Code - Over-the-Range Microwave - Product Help | JennAir

JennAir Product Help (producthelp.jennair.com)

dateModified 2021-04-27; PH 9587 / PH 9587 (over-the-range microwave)

Scope: JennAir over-the-range microwave. Read from the JennAir Product Help page for this code in the over-the-range microwave error code tree (November 2026).

Here to help

Good questions.
Clear answers.

Talk to our team
What temperature triggers E24?

JennAir states an overheat condition of 500 F (260 C).

Which parts are named?

Both sensors, the board and the wiring.

Is the microwave unsafe after E24?

Let it cool, reset it, and test briefly. If the code repeats, stop using it and book a visit.

Does E24 mean a fire?

The page does not say so. If you see smoke or flames, leave the microwave closed, switch off power at the breaker and call emergency services.

Let’s take care of it.

Something on the display?
Send us the details.