Model-specific code library

JennAir microwave error codes.

Fourteen messages are decoded for the JennAir over-the-range microwave, from keypad SE and sensor E-codes to F-code heating and fan entries, the DOOR message and Demo mode. Many of them end in a breaker reset.

Microwave code finder

Demo is a practice mode, not a failure. If dOn or dOff just appeared, demo mode was switched on or off. To toggle it, open the door, hold keypad 3 for five seconds until the d icon lights, then press Start within five seconds.

Read the Demo checks
Or choose

14 researched microwave codes. Each model reads codes its own way, so go by your own manual.

Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work

Messages with a manual behind them.

Demo

Demo mode

Demo is a practice mode, not a failure. If dOn or dOff just appeared, demo mode was switched on or off. To toggle it, open the door, hold keypad 3 for five seconds until the d icon lights, then press Start within five seconds.

Information only
DOOR

Door and latch

DOOR (or OPEN/CLOSE DOOR) means the door has stayed closed for five minutes or more without the microwave being started. This prevents unintended starting. Open and close the door, then start the cycle.

Owner checks first
E03

Keypad

With E03 the control board received a problem report from the keypad, which JennAir also calls the user interface. The keypad or its wiring may be the cause. Turn off the breaker that serves the microwave, leave it a full minute, then switch it back on and see whether E03 returns.

Reset, then book
E11

Sensors

With E11 the control board received a problem report from the gas sensor. The sensor or its wiring may be the cause. Shut off the microwave breaker for a minute, switch it back on and see whether E11 comes back.

Reset, then book
E21

Sensors

With E21 the control board found the thermal sensor circuit open. JennAir lists the sensor, the board or the wiring between them. Switch the microwave breaker off for a minute and back on.

Reset, then book
E23

Heating

With E23 the oven failed to reach preheat temperature in thirty minutes. JennAir lists the heater, the board that drives it, or the wiring. Turn the microwave breaker off for a minute, then on.

Reset, then book
E24

Sensors

With E24 the cavity registered an overheat reading of 500 F (260 C). JennAir lists the thermal sensor, the gas sensor, the board or the wiring. Turn the microwave breaker off for a minute and on again.

Reset, then book
F2H1

Fans and ventilation

F2H1 points at the switch that runs the vent fan and light, found on the lower left front side panel, or at its wiring. Turn the microwave breaker off for a minute, then on.

Reset, then book
F3H1

Sensors

F3H1 says there may be a problem with the humidity sensor or the associated wiring. Turn the microwave breaker off for a minute, switch it back on, and keep the oven in view for the next minute.

Reset, then book
F3T3

Sensors

F3T3 points at the thermistor that reads hood temperature, or at its wiring. Shut off the microwave breaker for a minute, switch it on, and keep the oven in view for a minute.

Reset, then book
F3T4

Heating

F3T4 says there may be a problem with the magnetron temperature thermistor or the associated wiring. Turn off the microwave breaker for a minute, turn it on, and keep the oven in view for a minute.

Reset, then book
F7E9

Fans and ventilation

F7E9 asks whether the vent is blocked. The upper vent door must open and close freely; trim, cabinetry or something else in the way could let the microwave overheat. Clear it, then turn the breaker off for a minute and back on.

Check, then reset
F9Q1

Keypad

With F9Q1 the oven could not carry out a function. JennAir names the touch pad, also called the user interface, or its wiring. Turn the microwave breaker off for a minute, turn it on, and keep the oven in view for a minute.

Reset, then book
SE

Keypad

SE points at the keypad, also called the user interface, or at its wiring. Turn the microwave breaker off for a minute, turn it on, and keep the microwave oven in view for a minute.

Reset, then book

Start with the model boundary.

Black countertop microwave with a small display, six pads and a dial, on a dark stone counter in a kitchen.

Fourteen over-the-range microwave messages, from SE to DOOR.

Fourteen messages are decoded for the JennAir over-the-range microwave, from keypad SE and sensor E-codes to F-code heating and fan entries, the DOOR message and Demo mode. Many of them end in a breaker reset.

Every page is the over-the-range microwave. Built-in and countertop JennAir microwaves are not in the pages we read.

Choose the next safe action.

Read the whole display

Give the code with spaces as shown (F7 E9 reads as F7E9), whether the fan is running, and the model number.

Respect the service boundary

Switch off the breaker before a reset, and never run the microwave empty. Leave the cabinet and the latches to a technician.

Documents checked for this library.

  • SE - Error Code - Over-the-Range Microwave - Product Help | JennAir
  • F7 E9 - Error Code - Over-the-Range Microwave - Product Help | JennAir
  • F9Q1 - Error Code - Over-the-Range Microwave - Product Help | JennAir
  • F3T3 - Error Code - Over-the-Range Microwave - Product Help | JennAir
  • F2H1 - Error Code - Over-the-Range Microwave - Product Help | JennAir

Go by the instructions for your own model. See how we research these pages.

Here to help

Good questions.
Clear answers.

Talk to our team
Are these microwave meanings universal?

Every page is the over-the-range microwave. Built-in and countertop JennAir microwaves are not in the pages we read.

What should I include when I report a microwave code?

Take a clear photo of the whole microwave display and of the model label. Add what the appliance was doing when the message came up, and do not borrow the explanation for a different appliance.

Why is a microwave code shown without any explanation?

An old search phrase is no substitute for manufacturer evidence. When our microwave documents leave a message undecoded, we show the name only and send you toward help, with no part or cause attached.

Where do I verify which microwave models a document applies to?

Browse the manufacturer documents in this microwave library and hold the models on their covers up against your label. Another model needs instructions of its own.

Let’s take care of it.

Something on the display?
Send us the details.