What it means
F3 E5 appears only in the wall oven tables. JennAir names one of the sensors, the control, or the wiring, and asks for a one-minute breaker reset followed by a one-minute watch.
JennAir oven F3E5 / Temperature sensor
F3 E5 appears only in the wall oven tables. JennAir names one of the sensors, the control, or the wiring, and asks for a one-minute breaker reset followed by a one-minute watch.
Also shown as F3E5
F3 E5 appears only in the wall oven tables. JennAir names one of the sensors, the control, or the wiring, and asks for a one-minute breaker reset followed by a one-minute watch.
Keep the door closed so heat does not leak into the rest of the stack.
F3 E5 returns after the reset or the lower oven stops heating.
Checks you have ticked / saved in this browser

Keep the door closed so heat does not leak into the rest of the stack.

Switch it back on and look at the display for a full minute.

Check that the other cavity still works. It tells you whether the control or only one cavity is affected.

JennAir prints it as F3 E5 with a space; keep that spelling in your note.
Send the model and the checks you have already run, then begin your request from this page.
Book a visit
A simplified drawing, because layouts change with the model. Tap an outlined part to see a photo and the related check.

Component reference
JennAir Product Help ties F1, F2 and several F3 codes to the oven temperature sensor, the control or the wiring between them.
Read the definitionOnly in the Wall Oven tree, as PH 13339. A freestanding range has no F3 E5 page, so a range showing it should be checked against other pages.
Read the supporting manualone of the sensors, the control, or the wiring that links them. Pages for E5 through E9 on wall ovens repeat the same wording, so the page cannot tell E5 apart from its neighbors.
Read the supporting manualJennAir does not explain it. We treat the E digit as an identifier a technician can read from the control's own log; we are not claiming it names a specific sensor.
Read the supporting manualDo the reset, then book if the code returns. Avoid forcing a lower oven to cook while it throws the code on a premium stack.
Read the supporting manualManufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2024-11-08; PH 13339 / PH 13339 (wall oven)
PH 13339: F3E5, wall-oven.
JennAir's wall oven text reads almost the same for both. The pages do not state a difference, so rely on the reset and a technician's tests.
If it runs normally after the reset, many owners do, but a repeat code is a warning. Plan a backup and book a visit afterward.
The page covers the lower oven only. Try the upper cavity to confirm.
JennAir prints E5 through E9 in the wall oven tables where a double oven has more than one cavity to report.
Code or symptom, part, service call
F3 on a JennAir freestanding range or wall oven points at the oven control or its wiring, and on a steam wall oven the page only asks for a breaker reset. Switch the oven breaker off for a single minute, switch it back on, then watch the display for another minute.
JennAir says not to judge oven temperature with a thermometer, because the elements cycle and most thermometers react too slowly. Check preheat time, racks, pan spacing and foil first, then run the biscuit test before any calibration.
JennAir Product Help ties F1, F2 and several F3 codes to the oven temperature sensor, the control or the wiring between them. The sensor reports cavity heat to the control. The help pages pair it with the control, so one reset is the only owner step.
Schedule a diagnostic for your model, carried out at the appliance.
Office details, plus the access notes to pass along.