On this page
- Press Cancel before you touch the breaker. 2
- The standard reset is one minute off, then one minute of watching the display. 12
- A professional-style range F5E0 has two page editions: one minute and five minutes. 56
- A returning F9 points to the home electrical supply; an electrician checks it. 4
- A steam oven restarts with a cycle, not a bake. 7
What does a power reset do on a JennAir oven?#
It restarts the oven's electronic control. JennAir's Product Help describes it as a way to remove some error codes: switch the breaker or fuse off for one minute, switch it back on, then watch the oven for a minute to see that the code does not return. 1
That is the whole idea. A reset does not repair anything, and it is not a cure for every code. It is the step the pages ask for before they ask for a technician.
Codes can print as F then a number then E then a number, or the other way round. 1 Read the characters exactly as shown before you reset; a technician will ask for them.
What should I do before I reach for the breaker?#
Press the Cancel pad. JennAir's Press Cancel to Reset page says that message appears when the control has detected a problem, and Cancel is the first answer. Only if Call Service shows after Cancel does the page move to a power reset. 2
So the order is simple. Cancel, look at the display, and if it has cleared, carry on. If it has not, or the same message shows again, reset the power.

Some messages are not errors at all. A flashing clock after a power cut, or a Lock message, has its own simple answer, and a breaker reset is not what those pages lead with. The power outage guide covers those.
How do I do the one-minute reset?#
Switch off the oven's breaker or fuse, wait one full minute, switch it back on, then watch the display for one more minute. For a range or wall oven, JennAir's pages add that you should start a bake cycle to see the oven run. 12
- 1
- 2
- 3
- 4
- 5

The same five steps appear on the page for an F0 E0 message. That message appears when the electronic control cannot tell what kind of problem happened. JennAir's page says the cause could lie in a part of the oven control system, the electronic control or its wiring, and gives the one-minute reset as the owner step. 3
When is five minutes the answer instead?#
On a professional-style JennAir range, the later edition of the F5E0 page asks for five minutes with the range disconnected, after a door check. The earlier edition of the same code says to turn the temperature knob to OFF and power down for one minute. 56
Here the two pages disagree, and both are JennAir's own. The page edited 2024-11-05 says turn the Temp knob to OFF to cancel the error, then, if it persists, turn the breaker off for one minute, restart the cycle and monitor for one minute. 5 The page edited 2025-10-01 says to check the door first, then reset the control by disconnecting power for five minutes, unplugging the unit or switching off the breaker. 6
When you cannot tell which edition your range follows, take the longer wait. The longer wait costs only four extra minutes.
The door check on the newer page is worth doing on its own. Open the main oven door and look at the door latch. If a notch or space is visible, the page says the door was not installed properly. Reinstall it so that the notch is fully inserted, and you should hear a click when the hinge is seated. 6 If you took the door off for cleaning recently, start there; the oven door guide covers how it goes back on.
Why would the error come back?#
Because the reset restarted the control but did not touch whatever set the error off. A code that returns inside the one-minute watch means the reset did not clear it, and the pages stop offering owner steps. 12
An F9 on a wall oven is the clearest case. JennAir's page says this code most often means the appliance is wired incorrectly at the home supply or the hard-wire connection, for example with the L2 and N conductors swapped, and tells you to have a qualified electrician check the supply. 4 The overview page adds that a recent installation, about three months, is a reason to call the electrician early. 1
The same page names two reasons a one-minute reset can clear an F9: line noise during a power outage that the control read as the wrong voltage, and keys pressed during the 10-second delay at power-up. 4 The F9 code page lists the other F9 variants for ranges.
What about steam ovens and locked doors?#
A steam oven follows the same reset, except you start a cycle at the end. JennAir's steam oven pages for F2, F3, F5, F8, F9 and F13 each say to power down for one minute, power up, start a cycle and monitor the oven for one minute. 7
A locked door is a different case. JennAir's Oven is Locked page lists several fixes, and the breaker is only one of them: press Cancel/Off to start a latch reset and wait 20 to 30 seconds, or switch the power off at the breaker or fuse box for one minute. It also says to let the oven cool for roughly 30 to 90 minutes and move the latch arm to the left. 8
If the lock was started by mistake, the same page says the oven must cool to about 200°F (95°C) before the door opens. 8 Do not pull on a locked door.
The code pages carry the rest: F2, F5 and F9 each list their variants, and the oven service page shows what we repair on a built-in oven.
Is it worth resetting more than once?#
You do not need to wait long. Do the reset once, timed by a clock, and watch the display for a minute. If the error appears again, further resets will tell you nothing new. 12
Write down the exact characters on the display, whether the error showed at power-up or during a cycle, and the model number from the oven's rating plate. Then ask us for a visit; the model number lets us check the right edition of the page first.
Sources#
- Error Codes for Cooking Appliances - Product Help | JennAirJennAir Product Help (producthelp.jennair.com) · dateModified 2025-10-16; PH 686 · PH 686
- Press Cancel to Reset - Range - Product Help | JennAirJennAir Product Help (producthelp.jennair.com) · dateModified 2024-11-07; PH 13131 · PH 13131
- F0 E0 - Error Code - Range - Product Help | JennAirJennAir Product Help (producthelp.jennair.com) · dateModified 2024-08-16; PH 12938 · PH 12938
- F9 or F9 E0 - Wall Oven - Product Help | JennAirJennAir Product Help (producthelp.jennair.com) · dateModified 2025-11-13; PH 13389 · PH 13389
- F5E0 Error Code - Commercial Range - Product Help | JennAirJennAir Product Help (producthelp.jennair.com) · dateModified 2024-11-05; PH 13096 · PH 13096
- F5E0 Error Code - Commercial Range - Product Help | JennAirJennAir Product Help (producthelp.jennair.com) · dateModified 2025-10-01; PH 14149 · PH 14149
- F2 - Wall Oven - Product Help | JennAirJennAir Product Help (producthelp.jennair.com) · dateModified 2024-11-08; PH 13439 · PH 13439
- Oven is Locked - What to Do - Product Help | JennAirJennAir Product Help (producthelp.jennair.com) · dateModified 2025-10-16; PH 698 · PH 698


