What it means
FC E6 names the Wi-Fi power module or its wiring on a JennAir range or wall oven. Reset the breaker for 60 seconds; if the code returns, the module needs a technician.
JennAir oven FCE6 / Wi-Fi hardware
FC E6 names the Wi-Fi power module or its wiring on a JennAir range or wall oven. Reset the breaker for 60 seconds; if the code returns, the module needs a technician.
Also shown as FCE6
FC E6 names the Wi-Fi power module or its wiring on a JennAir range or wall oven. Reset the breaker for 60 seconds; if the code returns, the module needs a technician.
The display, bake and broil should behave normally; if not, tell the technician.
FC E6 returns after the reset.
Checks you have ticked / saved in this browser

The display, bake and broil should behave normally; if not, tell the technician.

Restore power and wait for the oven to start up.

This is a hardware message, so restarting the router will not help.

Give both when you book.
Send the model and the checks you have already run, then begin your request from this page.
Book a visit

A simplified drawing, because layouts change with the model. Tap an outlined part to see a photo and the related check.

Component reference
The Wi-Fi module links a connected JennAir oven to your router.
Read the definitionIt supplies power to the oven's Wi-Fi circuitry. JennAir lists it, or its wiring, for FC E6.
Read the supporting manualE1 to E3 point to the network. E6 names a part inside the oven, so network fixes are unlikely to clear it.
Read the supporting manualE9 prints the same power module wording.
Read the supporting manualThe page gives no warning. A module problem touches connected features, not the heating.
Read the supporting manualManufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2024-08-16; PH 13001 / PH 13001 (range)
Manufacturer document
JennAir Product Help (producthelp.jennair.com)
dateModified 2024-11-08; PH 13245 / PH 13245 (wall oven)
PH 13001, 13245: FCE6, range/wall-oven.
The page does not say. It lists only the Wi-Fi power module or its wiring, so if FC E6 returns after the breaker reset, a technician needs to look at the module.
Yes, by a technician. It is a part inside the oven, not something an owner swaps, so book a visit if the code returns after the 60-second breaker reset.
No. A wall oven is hard-wired, so there is no plug to pull. Reset it at the breaker for 60 seconds instead, then restore power and let it start up.
Probably not until it is fixed, since FC E6 names the module that powers the Wi-Fi circuitry. Connected features are affected, the heating is not, and the page gives no warning.
Code or symptom, part, service call
JennAir prints no bare FC. FC E1 to E9 are connected-appliance codes on ranges and wall ovens: E1 to E3 and E7 say the oven could not reach your router, E4 and E5 name the Wi-Fi antenna, E6 and E9 the Wi-Fi power module, and E8 is a registration entry error. Start with the home network.
JennAir says not to judge oven temperature with a thermometer, because the elements cycle and most thermometers react too slowly. Check preheat time, racks, pan spacing and foil first, then run the biscuit test before any calibration.
The Wi-Fi module links a connected JennAir oven to your router. FC E1 to FC E3 mean the appliance could not connect; FC E4 and FC E5 name the antenna; FC E6 and FC E9 name the power module. A router restart is the first owner step; the oven itself still bakes.
Schedule a diagnostic for your model, carried out at the appliance.
Office details, plus the access notes to pass along.