Model-specific code library

JennAir oven Professional-style range light codes

11 printed codes in this group: Blinking amber light and tones, Controls are blinking (connected range), Griddle cooktop light, Reading error codes by LED (F#E#), Remote indicator light, Start button blinking, Start button solid light (Sabbath), Temp/Mod knob light, Tones (beeps), White blinking lights, Start button and 1 more.

Inside a range oven the lamp cover sits on the rack beside an empty lamp socket, with an unplugged power cord lying on the oven floor.
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work

Professional-style range light codes

Blinking amber light and tones

Amber lights that blink with three short tones and one longer tone mean a professional-style JennAir range has stored an error. Turn the Mode and Temp knobs to any new position, then set Mode to Bake and Temp to Off. If the amber lights return, the range needs a technician.

Reset, then book
Controls are blinking (connected range)

If a connected professional-style JennAir range is blinking its controls, the JennAir app can show why. Open the app, go to Settings, then Service and Support, then Appliance Error. The range must be registered in the app first.

Information only
Griddle cooktop light

On a JennAir professional-style range with a griddle, the right indicator glows solid blue while the griddle is on, and the left indicator flashes blue during preheat and turns solid when the preheat temperature is reached. These are status lights, not errors.

Information only
Reading error codes by LED (F#E#)

A JennAir professional-style range shows codes by lights. When the Wi-Fi LED and the Remote LED flash, an F#E# code is present: the Wi-Fi LED is the F part, the Remote LED is the E part, and the Mode knob's eight LEDs flash once per unit. JennAir's example: F5E3 is five flashes, then three.

Owner checks first
Remote indicator light

The Remote indicator on a JennAir professional-style range glows white when the range is remote-enabled. With the range idle, all indicators are off. It is a status light, not an error.

Information only
Start button blinking

A blinking Start button on a JennAir professional-style range is normally a prompt: after you pick a mode and temperature, it flashes white after two seconds to ask for Start. A fast blink with a tone means an invalid knob combination, and without Start within two minutes the range times out to idle.

Information only
Start button solid light (Sabbath)

On a JennAir professional-style range, only the Start button lit and solid means Sabbath Mode is on. It is not an error. Only the Bake cycle runs, as one continuous cycle, with no tones. To leave the mode, follow the exit steps below.

Information only
Temp/Mod knob light

The temperature knob light on a JennAir professional-style range glows solid white for a valid selection or finished preheat, blinks white for an invalid mode and temperature pair with a tone every 30 seconds, and blinks amber when the oven is too hot to proof or a drop of 100 degrees or more is under way.

Information only
Tones (beeps)

A JennAir professional-style range beeps at power on, when switched to off, at the start of a valid cycle, for an invalid Start selection, for an error with the unit, when preheat finishes and when an app timer ends. A tone alone is not an error.

Information only
White blinking lights, Start button

Solid white controls with a blinking Start button on a JennAir professional-style range usually mean Start was pressed before it began to flash. Rotate Mode to a new position, return Temp to Off, choose again and wait for Start to flash. White blinking while the oven climbs to a raised temperature is normal.

Information only
Wi-Fi indicator light

On a JennAir professional-style range the Wi-Fi light glows white when the range is Wi-Fi enabled, and every light is off in Idle mode. If the Wi-Fi and Remote lights flash, a code may be present: the Wi-Fi light stands for the F part of it.

Information only

Let’s take care of it.

Something on the display?
Send us the details.