Model-specific code library

JennAir oven Microwave (combination oven) codes

14 printed codes in this group: F1E3, F1E4, F1E6, F4E0, F4E2, F4E3, F4E4, F4E5, F4E6, F4E7 and 4 more.

Stacked microwave and wall oven, the microwave door open and a hand holding its control panel aside to show the board, with an unplugged cord on the counter.
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work

Microwave (combination oven) codes

F1E3

F1E3 on a JennAir combination wall oven names the microwave appliance manager or its wiring. The page asks for a one-minute breaker reset: switch off, turn back on, then watch the oven for a minute to see whether the code returns.

Reset, then book
F1E4

F1E4 on a JennAir combination wall oven names the microwave appliance manager, the microwave power relay or their wiring. Switch the breaker off for one minute, turn it on and watch the oven for one minute. If F1E4 comes back, book a technician.

Reset, then book
F1E6

F1E6 on a JennAir combination wall oven names the microwave thermistor or sensor, or the wiring that serves it. The printed step is a one-minute breaker reset followed by a minute of watching. Book a technician if F1E6 returns.

Reset, then book
F4E0

F4 E0 on a JennAir wall oven names the microwave inverter or its wiring. Turn off the oven's breaker for about a minute, restore power, and see if the microwave side runs without the code returning.

Reset, then book
F4E2

F4 E2 on a JennAir wall oven names the microwave sensor or thermistor, the microwave appliance manager, or wiring. Reset the oven's breaker for about a minute and see if the microwave side stays clear.

Reset, then book
F4E3

F4 E3 names the microwave exhaust air temperature sensor or its wiring on a JennAir wall oven. Cycle the breaker for sixty seconds; if the code stays away, keep an eye on the vent airflow.

Reset, then book
F4E4

F4 E4 names the microwave humidity sensor, the microwave appliance manager or wiring on a JennAir wall oven. Reset at the breaker for a single minute, then try the microwave again without the sensor-based cooking modes.

Reset, then book
F4E5

F4 E5 names the microwave weight sensor or wiring on a JennAir wall oven. Reset the oven's breaker for about a minute; if the code stays away, avoid weight-based automatic programs until checked.

Reset, then book
F4E6

F4 E6 names the microwave wave guide temperature sensor or its wiring on a JennAir wall oven. Reset at the breaker for sixty seconds, and never run the microwave empty while you test it.

Reset, then book
F4E7

F4 E7 names the microwave meat probe, its receptacle or the wiring on a JennAir wall oven. Take the probe out, inspect it, seat it fully if you use it, then reset the breaker for about a minute.

Reset, then book
F4E8

F4 E8 names the microwave inverter or its wiring on a JennAir wall oven, the same wording as F4 E0 and E9. Reset at the breaker for about a minute and stop microwave use if it returns.

Reset, then book
F4E9

F4 E9 is the third inverter row on JennAir wall ovens, worded like F4 E0 and E8: the microwave inverter or its wiring. Reset the breaker for a single minute and keep the microwave off if the code returns.

Reset, then book
F6E7

F6 E7 names the microwave appliance manager or its wiring on a JennAir combination wall oven. Reset the breaker for about a minute, then check whether the microwave side starts.

Reset, then book
F6E8

F6 E8 lists the microwave appliance manager control or its wiring on a JennAir combination wall oven. Reset at the breaker for about a minute and test the microwave with a cup of water.

Reset, then book

Let’s take care of it.

Something on the display?
Send us the details.